Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - rosco

Pages: [1] 2 3 ... 9
1
CB350/400 / Re: speedo trip rewind knob
« on: June 30, 2022, 03:06:24 PM »
May be deep, But true.   If you don't learn you keep making the same mistakes over and over ??

2
CB350/400 / Re: speedo trip rewind knob
« on: June 30, 2022, 10:08:24 AM »
Wish i had known this before  Never mind  Its not a crime to make a mistake !! But its a crime not to learn from it ?? Ross

3
CB350/400 / Re: speedo trip rewind knob
« on: June 29, 2022, 10:00:04 AM »
Cheers for that Matt.  If Peter hasn't got any  then i will take you up on your offer

Well Paul, you learn stuff everyday I never knew they unscrewed   Only read that to remove the knob use a dremel to cut a slot in the knob which can be repaired  This i was trying but totally destroyed the Knob  Every day a school day That is now logged Thanks

Ross

4
CB350/400 / Re: speedo trip rewind knob
« on: June 28, 2022, 10:36:36 PM »
Peter has just messaged me  He is away till the weekend but may have one

5
CB350/400 / Re: speedo trip rewind knob
« on: June 28, 2022, 02:56:37 PM »
Was talking with him about faces etc and he suggested cb750faces for the parts Just assumed he didn't stock any But worth a message cheers

6
CB350/400 / speedo trip rewind knob
« on: June 28, 2022, 01:51:08 PM »
Hi All
 Does anyone have a speedo trip rewind knob for a cb400  that they are willing to part with  It is a push fit on splines Unfortunately had to distroy mine while doing a refurb and they are not listed as a spare Thanks  Ross

7
Hi Ted   I also asked questions Although I'm not interested   They did reply to say it was UK registered  So i asked for Reg No  Engine No    and Frame No  so i could check the bikes history  So far no reply  Seems a bit suspect  Personally I would want to see it in the flesh  Better to walk away than get burnt

8
 HI All   If anybody is looking for stainless  fastners  Please check out  Kayfast in Wakefield  They do both A2 & A4 at very good prices and are very quick to send Worth checking   
Ross

9
CB350/400 / Re: Front fork strip down
« on: May 07, 2022, 06:27:11 PM »
I understand the bodge, but there are no leaks, as can be seen in photo No old staining on the paper I just don't understand why do it in the first place when its not needed ?????

10
CB350/400 / Front fork strip down
« on: May 07, 2022, 05:35:01 PM »
Stripped. The forks for re-chrome  Look what I found?… Kitchen roll packed in   Not sure why as there were no leaks The paper was dry  What are your thoughts???    Ross

11
CB350/400 / Re: Carb butterfly clips
« on: March 15, 2022, 03:29:52 PM »
400fourbits   has used ones if any good for you

12
Hi Ash My measurements  are the wire thickness 3mm Diameter of spring 17mm Number of coils is 18 As the bike is on its stand i cannot accurately measure length  If you want this measure let me know and i will take it off measure and send you a picture   Ross

13
Hi Ash  Just measured the spring on my CA77  I believe its the same part number   The wire is 3mm  and the outside diameter 17mm
            Hope this helps    Ross

14
Project Board / Re: Alloy tank
« on: February 06, 2022, 02:41:04 PM »
Hi Ian  Have a look at these   Tab Classics  and  The tank shop  Half price of what you've seen    Ross

15
CB350/400 / Re: Chrome plating
« on: January 15, 2022, 09:49:18 AM »
will check them out  I did get a quote from Agbrigg in Leeds @ £120+vat + postage for my front mudguard  Considering a new one
is £174 freepost   hummm

Pages: [1] 2 3 ... 9
SimplePortal 2.3.5 © 2008-2012, SimplePortal