Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Bryanj

Pages: 1 ... 462 463 [464] 465 466 ... 673
6946
CB350/400 / Re: Gearbox blanking seal.
« on: February 13, 2016, 10:27:44 AM »
Sorry not worth wrecking a gearbox trying to do a half assed job

6947
CB500/550 / Re: Gasket, seal, skim or bin?
« on: February 13, 2016, 10:20:12 AM »
Fine wet and dry used with oil and thoroughly washed off then new gasket

6948
CB750 / Re: cb750k Bits needed
« on: February 12, 2016, 06:39:01 AM »
Speedo drive is same as 500/550 and probably 500 twin

6949
CB500/550 / Re: Top Yoke ?
« on: February 12, 2016, 06:34:20 AM »
There is no rubber seal on the top yoke but there is one above and below each headlamp bracket

6950
CB500/550 / Re: Master Cylinder Holes Question
« on: February 11, 2016, 06:54:30 AM »
Not if its the Salperton tunnel

6951
CB500/550 / Re: Master Cylinder Holes Question
« on: February 11, 2016, 06:29:31 AM »
You can't possibly see the light at the end of the tunnel Trigger as contrary to the rumour that it has been turned off to save money in fact the bulb has been nicked!!

6952
CB500/550 / Re: Master Cylinder Holes Question
« on: February 10, 2016, 04:22:01 PM »
To see if its clear get one of the small torches (on obviously) and put it over the hole and look down the bore to see if you can "See The Light"

6953
CB500/550 / Re: Primary Shaft Bearing
« on: February 09, 2016, 07:34:47 AM »
one end is a 6322 the other a 6205 and the needle roller in the middle is a special

6954
CB500/550 / Re: To do before start up attempt?
« on: February 08, 2016, 06:50:56 AM »
With the plugs out and oil in turn over with the rocker caps off till you can see oil appear at the top end

6955
CB500/550 / Re: Gear shaft oil seal leak
« on: February 08, 2016, 06:48:49 AM »
Clean all the secret additive (sh1t) from inside the case and cover the splines on the shaft so as not to damage the inside of the seal then just push it in square

6956
Other Bikes / Re: Honda CB125T2 Restoration
« on: February 08, 2016, 06:45:26 AM »
Never saw one get that high as they were normally thrashed to death by little assholes

6957
New Member Introductions / Re: Newbie in London
« on: February 08, 2016, 06:41:18 AM »
Told you so!!!

6958
CB750 / Re: headlight glass
« on: February 08, 2016, 06:30:04 AM »
Not sealed beam in UK always a replacement bulb but US and some other countries had sealed beam which are frequently OK in UK as they dip straight up and down not with an angled cut off like cars. A standard 7 inch car unit will fit and if used in UK you should have a parking light or sidelight as that is the "obligatory" light

6959
CB750 / Re: Clutch slip
« on: February 08, 2016, 06:26:44 AM »
You dont adjust the springs, the bolts are done up tight and thats it so a set of plates and springs may be called for but try re-adjusting it first as it may have bedded in a bit anf the adjuster gone tight

6960
CB750 / Re: Yoshi style pipe in the UK??
« on: February 05, 2016, 05:24:46 PM »
If you find any you may have to fit the early exhaust stubs as I don't think Yoshi made them for the F

Pages: 1 ... 462 463 [464] 465 466 ... 673
SimplePortal 2.3.5 © 2008-2012, SimplePortal