This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Crispy
Pages: 1 ... 9 10 [11] 12
151
« on: March 16, 2018, 10:54:56 PM »
Update on this...I Paid a visit to David Silvers while in the area and got hold of a new collar... The pivot bolt fits through this one .....looks identical to the old one but obviously isn't...anyway problem sorted now thanks! 
152
« on: March 01, 2018, 07:31:16 AM »
Hi and welcome Andy ..I've not been on here long myself but finding loads of help and advice....good luck with the bikes!
Mick
153
« on: February 28, 2018, 05:03:33 PM »
I think that is what I will possibly end up doing, will check it on a new collar first but I am sending my fork top tubes there so could send it with them.
154
« on: February 28, 2018, 02:20:01 PM »
Hi, Yes that is a distinct possibility..it does look quite 'shiny'! That would also explain why the original collar was left out! Bit drastic tho...it's getting me a bit worried about what else that owner did..especially regarding the motor! 
155
« on: February 27, 2018, 10:38:20 PM »
Thanks Trigger...I'm ok for torque wrenches but that's all..I'll start by getting the fly wheel puller and clutch nut tool and then see what's what with the motor then
156
« on: February 27, 2018, 09:19:49 PM »
Well that's the engine stand sorted..thanks! .....might as well ask another question...are there any of the special Honda tools that I will not be able to manage without or will I need them all ? Don't really want to make do and damage things!
157
« on: February 27, 2018, 05:53:30 PM »
These SOHC people are amazing with help and advice.
I can second that..not been here long myself but already benefitting from help & advice!....welcome !
158
« on: February 27, 2018, 12:50:50 PM »
Didn't think I'd find one that quickly! ....Yes I'll have one please!
159
« on: February 27, 2018, 11:23:07 AM »
Well thanks for deciphering the replies for me Julie.....I would be interested in one...how much? ☺
160
« on: February 27, 2018, 07:39:09 AM »
I'm thinking I should get an engine stand before I start to dismantle my K1 motor ...any recommendations folks?
161
« on: February 26, 2018, 08:45:45 PM »
Well I measured the internal diameter of the collar 13.92mm and the external diameter of the Pivot Bolt 13.93 ..(an average of 4 measurements each) so I guess it's pretty close...there must be a bit of corrosion or other distortion somewhere...I'll just get a new collar when I get round to reassembly and see if it fits then. Pleased to have got the old bushes out without any hassle after following the tips picked up on this forum... thought that would be harder than it was ..thanks!
162
« on: February 22, 2018, 10:49:17 PM »
Mic the original spindle - o check if its not rusted, corroded and hence oversize - might have been damaged due to missing spacer. Conversely, check the bushes in the replacement swingarm in case they've been damaged - sounds obvious but got to be one or the other.
Cheers...will do that tomorrow..I don't suppose it would take much of a blemish to cause a problem.
163
« on: February 22, 2018, 05:52:06 PM »
No..both got the standard parts apart from the original missing the collar.
164
« on: February 22, 2018, 05:28:15 PM »
hi all,
hasn't taken long for me to ask my first question!
on stripping down my K1 swing arm I discovered it was damaged and ordered a replacement. It was upon examining the replacement that I realised that the collar ( part 12) was missing entirely from the original swing arm, no wonder it was damaged! The replacement looks identical but the original pivot pin (15) will not fit through the collar, according to the parts manual these parts are common to the K0,K1 & K2..it would be nice to know what am I missing here before I shell out on a new collar. Can anyone enlighten me?
165
« on: February 21, 2018, 11:09:07 PM »
Thanks again for the welcome folks 👍 Ay up me duck.. Welcome ! I go to Birchover, not far from Bakewell quite a bit, ...my bro-in-law & wife have a cottage there. Lovely part of the country. Loads of cheapo tools at the market on a Monday (lots of different Scotchbrite discs etc).
I know Bakewell market well..one of the wife's favourite places..🙄
Pages: 1 ... 9 10 [11] 12
|
Show Posts