Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sand5858

Pages: [1]
1
CB500/550 / Generator Cover and Rear Fender
« on: March 21, 2018, 02:41:46 PM »
Hello, there's someone here that has a generator cover and a Rear Fender for sale in here for a honda CB500 Four Vin. 2047312

Tony
Denmark

2
CB750 / CB 750 four link carburettor can not run at low rpm.
« on: May 25, 2015, 02:13:43 PM »
CB 750 sandcast can not idle at low rpm.

I have tried to adjust the throttle cable up through the throttle but it seems to adjust well beyond. I have adjusted the air screws around one turn out. Is there anyone who can come up with good advice to my carb problem.
Tony
Denmark

3
Announcements / CB 750 four link carburettor can not run at low rpm.
« on: May 25, 2015, 02:11:08 PM »
CB 750 sandcast can not idle at low rpm.
I have tried to adjust the throttle cable up through the throttle but it seems to adjust well beyond. I have adjusted the air screws around one turn out. Is there anyone who can come up with good advice to my carb problem.
Tony
Denmark

4
CB750 / Re: Restoration of Sandcast Frame 5369/ Engine E5479
« on: September 27, 2014, 07:39:11 AM »
Hi Pete.
I've been out in my garage to see the brake caliper I was talking about but unfortunately it is a Tokico 8 I have not so good for your Sandcast.
I will check up with a few friends if they have a Tokico 1 or 2

Regards
Tony

5
CB750 / Re: Restoration of Sandcast Frame 5369/ Engine E5479
« on: September 26, 2014, 03:16:46 PM »
Hey Pete.
I would also like to join in with a congratulations on your new project. You have happily taken a lot of pictures of all your projects, unfortunately I did not and I regret it now because a part of the restaurant is also taking pictures and maybe help others.
Have you thought about were you are going to buy a new front fender to the Honda- Yamiya  I'm even looking for a new front fender for my bike his is expensive but god repro..
Having written this into Google translate hope you understand this.

Only if you are interested I have a cam cover unfortunately cromed, and a brake caliper
Regards
Tony

6
CB750 / Re: Starter clutch
« on: September 15, 2014, 08:54:18 AM »
Hi Bryan.
Thank's but i have already buy'ed a starter kit. Now I just need to synchronize carburetors  4 cables on my Sandcast it is the last missing.
Thank you
Tony

7
CB750 / Re: Starter clutch
« on: September 15, 2014, 06:23:11 AM »
Hello, All.
Many thanks for your advice, I will try to change the rollers on the starter without removing the screws behind the generator.

thank you
Tony  8)

8
CB750 / Starter clutch
« on: September 14, 2014, 08:33:31 AM »
Hello there.
Is there anyone here who has tried to change the starter clutch on a CB750
I think that the Phillips screws that hold the hub in the clutch is very difficult to loosen.
Afterwards, the flywheel is mounted on the crankshaft and tighten with torque and I think this is also a challenge - something to have a friend on the motorcycle while I mount the flywheel.

All proposals received.
Regards
Tony

9
New Member Introductions / Newbie from Denmark
« on: August 13, 2014, 07:03:59 AM »
Hello everyone
A new newbie intrudoktion of me because yesterday I came to delete the first one I made here my fingers were faster than my brain ups.
thanks for the greetings from, among other AshiomotoKO and UK-Pete
Amazing project you are working on UK-Pete.
I put a few Picasalink in with what I am messing with.
Greetings from
Tony  ;)
Denmark
https://picasaweb.google.com/115342599141144427752/CB450MyFirstBike
https://picasaweb.google.com/115342599141144427752/MySecondBikeCB750Vin1001641WithK4Engine
https://picasaweb.google.com/115342599141144427752/SandcastProjectVin1005858?authkey=Gv1sRgCM_dvNOvtbvWqwE

Pages: [1]
SimplePortal 2.3.5 © 2008-2012, SimplePortal