Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Johnny4428

Pages: [1] 2 3 ... 139
1
CB500/550 / Re: Henry Coles 550K3 for sale
« on: May 16, 2024, 10:09:04 PM »
Descent looking bike even without the proper exhausts, but as Mick says those tank decals are awful! Not even close to what they should look like.

2
Misc / Open / Re: It's been a Shite yesr
« on: May 16, 2024, 09:24:49 PM »
Bryan that’s a bloody raw deal you have been dealt with in terms of your family etc, but it’s testament to you for your unwavered and continued assistance through the forum to assist people with comparably trivial problems. Well done for that and all the best mate!

3
SOHC Singles & Twins / Re: My first project - 1974 CB360 K0
« on: May 13, 2024, 06:09:31 PM »
😂😂🤭 You won’t be the first or last to do something silly! At least you’re willing to admit it too. Very satisfying to get it sorted too.

4
Anorak's Corner / Re: Anyone used ABS Slurry to fix side panels etc
« on: May 13, 2024, 10:00:38 AM »
Nice one Ian! You’ve got me converted from fibre glass!

5
Misc / Open / Re: Thanks are overdue from Lazarus
« on: May 13, 2024, 09:56:18 AM »
Nicely put Mick and echo your praise for the forum. Enjoy your bike, all the head scratching will pay off in the end!😜

6
Project Board / Re: Teds new project a CB500 K1 mostly version 0.5 circa 1972.
« on: May 13, 2024, 09:42:29 AM »
Ted that all sounds exhausting! (somebody had to do it). Sounds like you’ve done a good job there bike is starting to look like it’s about ready to roll. It’s a shame when parts are made for a specific model that they don’t fit correctly, especially going to the expense and trouble to produce a quality replacement.😡

7
CB350/400 / Re: Anyone recognise this bit?
« on: May 09, 2024, 09:58:28 PM »
Any snipers around there Roo? 😂😂

8
Project Board / Re: Teds new project a CB500 K1 mostly version 0.5 circa 1972.
« on: May 09, 2024, 09:56:44 PM »
Nice work there Ted! Shapeing up to be a nice bike!

9
CB500/550 / Re: Rear wheel rotation stiffens up when tightening axle problem.
« on: May 09, 2024, 05:39:41 PM »
Good work there Ted! Had to do similar work on my replacement shoes on the 550 except they weren’t binding when fitted.👍

10
Out & About / Re: OUT AND ABOUT 2024
« on: May 09, 2024, 05:34:06 PM »
Looks like a lovely part of the country there John!

11
What is it? / Re: Mysterious Exhaust Teeth
« on: May 08, 2024, 09:32:19 PM »
Quote from: K2-K6 on May 08, 2024, 12:13:21 PM
Has a previous custodian filed teeth in them to id for each cylinder ?

Perhaps owned by a dentist previously  ;D
😂😂😂

12
Out & About / Re: SOHC meet in Scotland
« on: May 08, 2024, 09:28:38 PM »
29th is fine with me Gareth! 👍

13
Out & About / First outing. 2024
« on: May 08, 2024, 08:57:56 PM »
Had a nice run out this morning after 6 to 7 month lay up for winter. She is running good.



Sent from my iPad using Tapatalk

14
CB500/550 / Re: top end gasket set recomendations
« on: May 06, 2024, 10:10:12 PM »
Check the thickness of new gasket compared with old and the difference then added to standard o ring thickness.

15
Humour / Re: MBE
« on: May 04, 2024, 10:09:48 PM »
🤭🤭😂

Pages: [1] 2 3 ... 139
SimplePortal 2.3.5 © 2008-2012, SimplePortal