1
Announcements / 400/4 fuelTap Filter .
« on: April 15, 2023, 07:30:43 AM »
Hi does anyone know where to get the rubber seal for the Filter assembly without buying the Whole set . Thanks .
Try our new info resource - "Aladdin's Cave" (Main menu)
Just added a separate link to Ash's Dropbox thread (shortcut)
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
1
Announcements / 400/4 fuelTap Filter .« on: April 15, 2023, 07:30:43 AM »
Hi does anyone know where to get the rubber seal for the Filter assembly without buying the Whole set . Thanks .
2
CB350/400 / CB350 Handlebars« on: February 23, 2021, 12:07:59 PM »
Would anyone Know if CB350f handlebars will fit my Cb400f ? I am looking for a set but having no luck .DSS has not got any same with CMS . I would consider a good second hand if anyone has a set . Thanks for reading !
3
CB350/400 / 400/4 Regulator rectifier wiring m« on: February 06, 2021, 10:32:41 AM »
Just bought new combined regRec unit from DSS . Wiring diagram not really clear how to hook up .main plug 3 yellow 1 red I green . Plus 1 BLACK WIRE splits into 2 . Question where do these go ? Thanks if anyone has fitted on recently .
4
CB350/400 / CB400/4 Front Wheel Speedo Drive« on: November 16, 2020, 05:25:35 AM »
Good morning all , I took my front wheel off to fix a flat tyre and ended up taking the Brake Disk off to clean and paint centre .Well while I was at it I decid to clean up front brake caliper . All that is now done but just wondering if I should grease wheel bearings and grease or Oil up Speedo Drive . I had a go at undoing the Centre bolt but after 45 years I won’t budge . Any ideas guys or should I just leave it alone .ie if it’s not broken leave it alone . Thanks for reading .
5
CB350/400 / CB 400/4 Front Disc need ideas for Cleaning up .« on: November 07, 2020, 06:12:55 AM »
Lots of Dodgy ideas on YouTube so thought I would ask the experts . Help !
6
Project Board / Honda CB Disc Rotor Cleaning« on: November 07, 2020, 06:07:39 AM »
Lots of different ideas on YouTube but I thought I would ask the Experts for Help . I have 75 4004
7
CB350/400 / Regulator/rectifiers Wireing need HELP« on: May 23, 2020, 08:29:35 AM »
Bought The CB400/4 with reg/rect off Honda integra 1985 it says . Birdsnest of wiring so put new harness on and new reg/rect to suit . Upon fitting blows a fuse and said reg/rect is letting current both ways on one of the diodes . The Old reg/rect which is testing ok and came with bike has an extra wire than the DS one I bought . Would any one know if I can use it on the new loom and which wires go we’re ?thanks if you can help .
8
CB350/400 / BUTCHERD 400/4 STARTER MOTOR« on: May 22, 2020, 07:35:53 AM »
This is the Starter Motor I got with the bike a few years back .Dont know what the Home Made holes in the back end are for but I think it is knacketd !
9
CB350/400 / 1975 400/4 reg/rect« on: May 21, 2020, 09:22:32 PM »
Well , while I’m on a roll . New regRect has a diode problem now . It’s letting current both ways on one diode . Just wondering if it’s going to damage the battery ? Help !
10
CB350/400 / 400/4 flat battery« on: May 21, 2020, 09:14:53 PM »
Bought bike a few years back (not running ) and on handing over cash got told (oh! there is a small short ) Well after putting on New battery new wiring loom new fuse box new reg/rect the Bloody thing would start then battery would go flat after a short ride . So last time it happend a mate says do you think it’s the starter motor ? No I says as it starts the bike . Well guess what . I changed the starter motor and it must have been the propblem as it turns over twice as fast now and doesn’t let you down after a short ride . Also on inspection some one had drilled two small holes in end don’t ask me why but that must have been the problem . So advice is look for the obvious and don’t buy a none runner unless it’s cheap (and mine wasn’t ) Happy riding folks ! PS flashers would also freeze when starter gave up ghost making you think it was the battery . No it was the flasher unit . Talk about coincidence Agh !
11
CB350/400 / 400/4 carb balancing« on: May 21, 2020, 03:36:21 PM »
Think they need a balance . Sluggish takeoff then whoosh! Anyone know a good brand of vac gauges or ones to avoid ? Thanks in advance!
12
CB350/400 / 400/4 Battery not charging« on: November 24, 2019, 05:01:12 AM »
Ideas needed for fix . At the moment I have to charge my battery off the bike . Fully Charged it lasts about Half an hour . Starts on the button then looses power fast no starter and indicators stop . If I fully charge and leave it over night it drains . So what’s wrong Guys ?
13
CB350/400 / 400/4 Exhaust Fitting Info needed« on: October 24, 2019, 11:12:42 PM »
I have inherited a set of replacement Pipes and collector box (Silvers ) for 400/4 . All brand new but no instructions . The pipes are marked 1 2 3 4 . My question is which way round do they fit the collector box ? I see on one side of said box has a fitting for a retaining bolt ( I don’t have ) The other three slots have nothing to hold pipes . So looks like press fit ! Any help welcomed.
14
CB350/400 / 400/4 collector Box/ pipes by LJS just saw his latest offering .£219 Plus Vat !« on: September 22, 2019, 02:29:23 AM »
Has any one tried these ? Thanks info needed !
15
CB350/400 / 400/4 Crank Oil Seal« on: July 19, 2019, 08:50:33 AM »
Opps , orderd oil pump seals to fix oil leak . Well after cleaning underside of pump ext just found oil is coming from lower crank cover Agh ! Having said that I find I have said crank oil seal ! DSS 91201-323-005P .Question is can I fit this seal without splitting crank cases ? Help !
Pages: [1] 2
|