This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - paulbaker1954
Pages: 1 ... 5 6 [7] 8 9 ... 47
91
« on: April 25, 2020, 08:46:51 AM »
Hi
Having had exactly the same issue as you here is my advice..
1) Use only OEM Head Gasket and O rings. I had bad experience with the DSS aftermarket set
2) Once the head is off I would recommend getting it skimmed to ensure it is flat. Shoul not cost a huge amount at a reputable machine shop (mine was £30 if I recall)
3) Read the manual Ash recommends and take your time especially with refitting the cam cover and cam chain etc to make sure you get valve timing right.
92
« on: April 25, 2020, 08:40:24 AM »
I am using my 500 for nipping oit for essential shopping such as Gin and Wine using my trusty 🎒
👍👍👍
93
« on: April 25, 2020, 08:20:09 AM »
Does anyone have any experience with UV resins for repairing plastic parts. I usually resort to reaching for the Superglue but seen some outrageous claims for this UV stuff. Seems to me that only really good for transparent materials as otherwise the UV will only cure the bond edges
Any other recommendations for high strength plastic repairs?
94
« on: April 11, 2020, 08:11:23 AM »
Paul, any update?
Sorry no update, project on hold for a while.
95
« on: February 21, 2020, 08:48:49 AM »
All sorted now was (no surprise) down to air leaks
Where about, Paul?
Carbs to inlet manifold rubbers
96
« on: February 19, 2020, 08:55:49 AM »
All sorted now was (no surprise) down to air leaks
97
« on: February 12, 2020, 04:43:48 PM »
Nice
I was also really pleased with the set I got from him and he honoured the £95 trade in on my old set with no hassle
98
« on: January 30, 2020, 04:19:54 PM »
nope
Thx that’s what I thought just wanted to be sure though👍
99
« on: January 30, 2020, 12:56:25 PM »
I bought an Electrex reg/rect a while ago and am just thinking of getting to fit it
The plug and play connector it came with won’t work as my bike is an early K0 with the round pins.
May be a stupid question but does it matter which way round the 3 yellow wires connect from the alt to the reg/rect unit?
100
« on: January 19, 2020, 08:09:02 AM »
I’m in
No 15👍👍
Will there be a SOHC area designated as last year I couldn’t get to it as the jobsworths said it was full?
101
« on: January 11, 2020, 12:45:26 PM »
I have signed up, always a good day out
Hopefully my mystery disease will be sorted by then 🤞🤞🤞
102
« on: January 08, 2020, 08:13:54 AM »
Ok gang all now posted to those who ordered 👍👍👍
103
« on: January 03, 2020, 05:12:44 PM »
Ok Have them in my sticky hands works out at £5 each inc postage
Will pm all those who ordered with payment details etc
Please let me know postage address in your PMs
104
« on: December 30, 2019, 05:03:35 PM »
Fitted m Gerben set of refurb carbs today, all synced up and my bike is running better than it ever has.
Wish I had made this investment ages ago he sure does a good job an highly recommended😀😀😀
105
« on: December 21, 2019, 07:53:46 PM »
Hi all
Gauges are now at work but sadly I have been ill with really shitty illness and just feeling nauseous and shitty most of the time(now 6 weeks in).
blood tests all fine and exploratory ct scan tomorrow. Doc seems a bit stumped so you will have to hang in till new year
Sorry for the delay
Pages: 1 ... 5 6 [7] 8 9 ... 47
|
Show Posts