This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - Arch stanton
31
« on: February 21, 2019, 01:41:07 PM »
Does anyone know if there is a Oil cooler that can be fitted to a 750k1 and still retain the standard horn?
32
« on: February 12, 2019, 01:43:01 PM »
I know this has probably been covered many times but...
What are my chain options on my 750k1?
I would really prefer O ring. But your thoughts would be appreciated.
Sean.
33
« on: February 12, 2019, 01:26:27 PM »
What is it, that makes some people think that including the word "Sandcast" when advertising something for sale.
Justifies a ridiculously high price?
Even if the part is common to other models.
34
« on: January 12, 2019, 02:39:30 PM »
On the 750k1 I am building. There is a yellow & red wire from the starter solenoid. There is also a matching wire from the harness in the same area. But they both have male connectors.
Is there something missing?
35
« on: January 02, 2019, 12:26:56 PM »
Hello.
Does anyone here know if the 750K1 switch differs from a
Cb175 switch?
Its just that I have a Nos 175 switch. That appears to match the 750 item. But I'm not sure if the contacts within the switch will make the correct connections.
Any help will be appreciated.
Sean.
36
« on: December 25, 2018, 08:14:39 AM »
Hello.
Has anyone on here got a Box section swing arm. To fit a 750k1. That they would like to sell?
Regards.
Sean.
37
« on: December 18, 2018, 12:48:26 PM »
Hello folks.
I am building a 750k1 almost from scratch. So I have no points of reference to work from.
What I need is a photo of the electrical department ie, under
The lh side panel.
Also where does the green earth lead connect to the frame?
I'm using a new wiring harness, which has a red wire with a male connector. I suspect that is for a fuse. But where should the other end of the fuse connect?
Any help & advice will be greatly appreciated.
Regards.
Sean.
38
« on: December 18, 2018, 12:47:31 PM »
Hello folks.
I am building a 750k1 almost from scratch. So I have no points of reference to work from.
What I need is a photo of the electrical department ie, under
The lh side panel.
Also where does the green earth lead connect to the frame?
I'm using a new wiring harness, which has a red wire with a male connector. I suspect that is for a fuse. But where should the other end of the fuse connect?
Any help & advice will be greatly appreciated.
Regards.
Sean.
39
« on: November 18, 2018, 11:44:46 AM »
Hello.
When I stripped my current 750k1 project. The wiring was a home made rats nest. So I just cut everything out.
But now I am installing a new harness & when looking through my box of electrical components I find a Diode. This was fitted to the bike when I got it. But the parts book doesn't show the K1 having a Diode.
I believe this Diode is to allow the bike to start in gear with the clutch pulled in.
My question is. Can this Diode be fitted into a standard K1?
And if so. Where does it go?
I'm afraid that I'm a real Dimmock where electrics are concerned.
Your help would be greatly appreciated.
Sean.
40
« on: November 03, 2018, 02:30:52 PM »
Just trying to install the front spindle.
But as soon as I get the spindle nut even hand tight.
The spindle binds.
Anyone any ideas what may be wrong?
Sean.
41
« on: October 28, 2018, 01:05:33 PM »
Hello.
Did the steering geometry change in any way between the K1
& K6 models?
What I need to know is. Will any K top yolk match a bottom yolk from another K model?
I have a K1. But I am fitting F1 forks etc. But I want to use a Set of K yolks. This will allow me to fit my F1 clocks closer together by eliminating the F1 centre console & using the far nicer looking K consol/bar clamp.
Yesterday I tried to put things together only to find there is a huge difference in offset between a K top yolk & F1 bottom yolk. So I now need a bottom yolk to match the top one I have. But I'm not sure which K my top yolk is from. Hence my original question. Are all K model tops & bottoms compatible?
Regards.
Sean.
42
« on: October 06, 2018, 10:11:56 PM »
Hello.
After reading comments on here regarding the weaknesses in the Cb750k charging system regarding headlight build wattages.
I'm wondering if there is any difference in output between the early K models & the F models?
I ask this because I used to use 100w/65w H4 bulbs in my old F1 without any charging problems. I did a lot of night riding at that time as the bike was my only transport.
Your comments would be appreciated.
Sean.
43
« on: September 15, 2018, 08:16:47 PM »
Hello Folks.
There must be someone on here that has used the clock faces supplied by CB750faces.com.
I have a pair, but i have noticed they are a lot lighter colour on the rear side thus letting a lot more light through.
So my questions are.
Do these faces light up correctly?
Or do they let too much light shine though?
Or even cast silhouettes of the clocks workings?
I'm thinking maybe i could use some self adhesive vinyl
On the back to prevent the problem I'm anticipating.
You're thoughts & experiences would be greatly appreciated.
Sean.
44
« on: August 31, 2018, 10:34:13 PM »
Hello.
Cb750k/Cb750f1 oil filter bolts.
Do they differ in length?
Sean.
45
« on: August 18, 2018, 02:12:28 PM »
Does anyone want a front DID rim in really quite good condition off a 750K1 also has non rusty spoke set?
Going in the skip otherwise.
Sean.
|
Show Posts