This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - brodsord
31
« on: April 28, 2020, 08:01:47 PM »
There’s no grooves I meant to add, the plates are smooth, they seem to have a diamond pattern etched in the surface
Sent from my iPhone using Tapatalk
32
« on: April 28, 2020, 07:59:55 PM »
Thanks all for your reply’s.
Hi Trigger yes it has the double plate in the middle.
I’ve just sent Andy at good bits a message to see if he is still doing internet orders, he has an updated lifter in his web shop and a complete clutch kit.
Is the double metal plate specific to different models?
Thanks
Gray
Sent from my iPhone using Tapatalk
33
« on: April 28, 2020, 05:58:21 PM »
Hi All, I’ve taken the clutch out the friction plates all measure around 2.40 to 2.70 ish mm Back friction plate in the picture below looks Mullered. The pressure plate also has been broken, it had been epoxy resined which was holding, am I ok to weld the broken tab back on or should it i get a new one? Also do I have to remove the inner clutch basket to fit new clutch plates or can just assemble them into the basket in situ on the bike? Thanks for any help    Sent from my iPhone using Tapatalk
34
« on: April 20, 2020, 09:02:25 AM »
Thanks Lobo, Yes mineral oil is what’s in there. Ill have a google this morning  Sent from my iPhone using Tapatalk
35
« on: April 19, 2020, 08:37:13 PM »
Ok thanks G I’ll have fiddle tomorrow. Sent from my iPhone using Tapatalk
36
« on: April 19, 2020, 08:21:31 PM »
Thanks G.
Should I replace them then?
Sent from my iPhone using Tapatalk
37
« on: April 19, 2020, 08:10:55 PM »
Hi everyone,
So I’ve got the old girl out for a quick road test.
F2 frame k5 engine.
All is good but Clutch is slipping after second gear.
Last time she was on the road was 1998.
Fresh oil in her etc and I’ve adjusted the clutch as per manual, do i need to replace clutch or is there something else I can do ?
Many thanks,
Gray
Sent from my iPhone using Tapatalk
38
« on: April 17, 2020, 03:09:55 PM »
Thanks so much Julie Sent from my iPhone using Tapatalk
39
« on: April 17, 2020, 02:51:10 PM »
Hi everyone,
My front drive sprocket has a slight bit of wiggle, if I hold it between thumb and fore finger it had a about a couple of mm movement, is this normal?
The engine is a K5.
Thanks
Gray
Sent from my iPhone using Tapatalk
40
« on: April 04, 2020, 05:10:11 PM »
Sent from my iPhone using Tapatalk
41
« on: April 04, 2020, 04:55:36 PM »
Posted from you*
Sent from my iPhone using Tapatalk
42
« on: April 04, 2020, 04:55:02 PM »
Thanks Dennis,
Did I read something posted from regarding this issue?
Sent from my iPhone using Tapatalk
43
« on: April 04, 2020, 04:26:53 PM »
Thanks BryanJ. It seems that is the norm, I can cope with that. Thanks for your reply Sent from my iPhone using Tapatalk
44
« on: April 04, 2020, 02:50:03 PM »
Hi John, hi K2,
Seems I can move through the gears ok,
I can’t seem to get her to go into neutral,
I’ve just rode her around my drive and same thing, changes gear ok but trying to get into neutral is very difficult.
Thanks for any advice.
Graham
Sent from my iPhone using Tapatalk
45
« on: February 29, 2020, 07:10:25 PM »
Thanks K2. I’ll get back to you both once I’ve got her on the stand. Thank you both for your advice. Sent from my iPhone using Tapatalk
|
Show Posts