This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Johnwebley
16
« on: April 27, 2024, 08:32:56 PM »
A great idea
Locally I can ride in bus lanes in a couple of towns, others, I am not sure
Let's have a firm,yes
Two wheels can use bus and taxi lanes
Sent from my SM-A546E using Tapatalk
17
« on: April 27, 2024, 06:48:00 PM »
Thanks guys,
May/June sounds great,
I shall start exploring links
Sent from my SM-A546E using Tapatalk
18
« on: April 27, 2024, 05:40:22 PM »
as the title says,I want to explore Scotland,
as I live in the west mid lands,its will involve a ride north,
my general plan is,
ride north,use the M6 to get past Manchester,then explore the local areas,
I amexpecting to ride around 300 miles a day,that can be adjusted,
so ideally a B&B north of Manc
I have a friend to stay with near Glasgow, I want to explore the islands,so info on ferries and B&B,so a nice cruise to John O'groats,
return south on the easter side,
similar into england,down as far as Lincilnshire,then home,
time is not critical, suggestions from those thatlive in the areas,
also reccomendations of places tovisit.
some thing for 2025
your help is appreciated
19
« on: April 27, 2024, 05:28:12 PM »
welcome Kev
lots of help and advice here,
and occasional chances to meet up
20
« on: April 27, 2024, 04:23:03 PM »
Totally agree
RIP off
Sent from my SM-A546E using Tapatalk
21
« on: April 27, 2024, 03:31:47 PM »
Couldn't you cut a piece of 6mm alloy to shape, drill for the screw,
Make a gasket, and fit??
Or you could buy a sheet of carbon fibre, the sort that is used for models,
Sent from my SM-A546E using Tapatalk
22
« on: April 27, 2024, 02:59:02 PM »
Extremely doubtful
Sent from my SM-A546E using Tapatalk
23
« on: April 26, 2024, 05:19:06 PM »
Could I suggest something I do,
Take the bike for a run about 15 to 20 miles get it nice and warm When home, keep the engine running, put on centre stand
Get your long screw driver
Now ,turn one airscrew a quarter turn out, Check what happens, blip the throttle, OK?
If it struggles,turn to previous settings
But if its OK,do another, repeat, and check
Remember, Modern fuel is different than 50years ago,
It might like a leaner tickover
Sent from my SM-A546E using Tapatalk
24
« on: April 26, 2024, 03:57:00 PM »
Can I suggest when you fit the replacement, make sure you don't over tighten it,
Sent from my SM-A546E using Tapatalk
25
« on: April 26, 2024, 08:27:48 AM »
I have a thought, the joints and the splines on the shaft drive,
I know a friend that had a K brick had issues
Sent from my SM-A546E using Tapatalk
26
« on: April 25, 2024, 08:53:01 AM »
Back in the 80s
I also used Champion A8Y
Definitely a projecting nose plug,
The bike ran well, but they became difficult to get
Sent from my SM-A546E using Tapatalk
27
« on: April 24, 2024, 04:35:20 PM »
Check for the washer between the spring and the oil filter. Often stuck to the oil filter and often accidentally binned. I have 3 engines here and none of them had the washer.
BTW mine are 400s, I imagine yours has a similar washer.
Yes, the 500 has them Fit between filter and spring Sent from my SM-A546E using Tapatalk
28
« on: April 24, 2024, 03:59:22 PM »
Good for you,
The idea of the small head, is to stop it being tightened to much,
I also grease the O ring under the head to prevent it sticking/corroding
Sent from my SM-A546E using Tapatalk
29
« on: April 23, 2024, 05:18:55 PM »
Actually, I run Denso x24ea-u
I believe that the are equivalent to the D 8ea
A d7ea is normal for the 500
The 8s are for 400,750 etc
Sent from my SM-A546E using Tapatalk
30
« on: April 23, 2024, 03:15:15 PM »
I dispute this,
My 500 has no issue
In fact, I use a harder plug than reccomended, an 8 instead of a 7 ,
I have checked the tickover mixture, and my airscrews are turned out more than normal,
I also have Boyer ignition, and run the plug gaps at 33thou,
Sent from my SM-A546E using Tapatalk
|