This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - SPR
1
« on: July 15, 2023, 10:05:05 AM »
2 clutch cables - one stamped made in Japan but has a slight nik on the cable coating - doesn’t catch on sleeve Price is for both £50 ono plus postage (welcome to collect from S42) Thanks Simon Sent from my iPhone using Tapatalk
2
« on: July 15, 2023, 09:18:55 AM »
That was quick !!!
SOLD to Tim
3
« on: July 15, 2023, 09:01:59 AM »
As new - used a couple of times £50 plus postage (welcome to collect from S42) Thanks Simon
4
« on: April 07, 2023, 05:50:39 PM »
Can't read the badge is it a Harley of some sort?
Yep ... a Dyna ... I've had a few before and like them - I sold the Laverda as I just couldn't get on with the RH gear change ( I suspect if an only bike it would be fine) ... made a tidy profit on it though !!
5
« on: April 07, 2023, 05:15:21 PM »
Lovely day out and about .... on the newly acquired bike Simon Sent from my iPhone using Tapatalk
6
« on: March 21, 2023, 08:18:42 PM »
Ken ... if you have a restored cb500 master cyclinder you want to sell ...... just sayin Simon
7
« on: March 17, 2023, 07:54:43 PM »
Should I lacquer the patches after painting? If so, what do I use?
No - nothing on top of the paint .... and practice to apply the right amount with a very soft bristled brush ....... just enough so it flows but not too much to run
8
« on: March 11, 2023, 12:28:38 PM »
I have ordered the Rust Oleum. Thanks.
Make sure it isn't too cold - or it is too thick to flow .... and stir well
9
« on: March 10, 2023, 04:48:38 PM »
I've had a tin of this for years and use it when required to touch in chips and small areas .... it flows very well and provides a great colour match
Rust Oleum Combicolor Original in black
10
« on: February 28, 2023, 08:36:50 PM »
Really sorry for the thread hijack Simon, I really wanted you to avoid the mistake I made with the clips, you have a lovely bike and it's important to me that you keep it that way, the 500 has always been MY bike, it's my first love so if I can keep one on the road that's worth going that little extra mile for. In an effort to stress how important it was to made I made that statement on your thread instead of starting a separate one which was always my intention. Sorry mate.
As always Ken I'm greatful for the advice ....... I'm thinking of using Sikaflex 221 which I've used before to repair and make seals .. I think a bead of it would easily stick to the tank lip and then hold the trim etc .... it holds its shape better than silicone - if that makes sense - and might be less messy Cheers Simon
11
« on: February 28, 2023, 06:18:17 PM »
I simply wouldn’t fit it as it looks gash in my opinion. Chrome is chrome, plastic coated metal of dubious quality doesn’t really do it for me especially as it’s a faff to fit, easily knackered and stuffs yer tank if not put on in a way and even then is a water trap. Each to his own though but personally after coughing up. For s paint job the lady thing is do is stick that garbage to it! ——————————————————————— Some will know why he’s going, some won’t but is a MASSIVE loss to this forum and a huge shame but I understand completely.
Sent from my iPhone using Tapatalk
It is actually exactly as fitted originally - in looks and fitment
12
« on: February 28, 2023, 12:44:07 PM »
Ken
Good points all and explains a method well - I’ll be avoiding clips !!
Your advice is always on point to is of lesser knowledge and hopefully you will stay around
Simon
Sent from my iPhone using Tapatalk
13
« on: February 28, 2023, 11:09:51 AM »
What you have to ensure is not leaving any pockets without silicone .... or it could be just as bad as a water trap as using clips
Sent from my iPhone using Tapatalk
14
« on: February 27, 2023, 03:43:42 PM »
Ken
Not fitted it yet or even offered it up .... tank was full
Sent from my iPhone using Tapatalk
15
« on: February 27, 2023, 11:10:50 AM »
Simon, if you get chance before fitting, could you tell me what material it's made of please. Does a magnet stick to it?
Julie - see previous reply - I found a magnetic tool tray and it doesn't seem to be metal ... They produced a youtube video showing installation which would suggest there is some extra to cut off .... do you want me to save it and send it you once complete ? https://youtu.be/c6_IArRGdBo
|