91
CB350/400 / Re: rotor removal tool. Also Gaskets
« Last post by Jan B on May 14, 2024, 06:10:13 PM »Did you check the ohm-readings on the 3 stator wires? That will tell you something. The regulator is more likely to fail...
Try our new info resource - "Aladdin's Cave" (Main menu)
Just added a separate link to Ash's Dropbox thread (shortcut)
91
CB350/400 / Re: rotor removal tool. Also Gaskets« Last post by Jan B on May 14, 2024, 06:10:13 PM »Did you check the ohm-readings on the 3 stator wires? That will tell you something. The regulator is more likely to fail...
92
CB500/550 / Re: What is the correct 500 rear brake light switch wiring route ?« Last post by McCabe-Thiele (Ted) on May 14, 2024, 05:30:10 PM »Thanks for that.👍
93
CB500/550 / Re: Relocating or alternative to ignition switch« Last post by Laverdaroo on May 14, 2024, 05:30:04 PM »No worries bud, just shout Dom
Sent from my iPhone using Tapatalk 94
CB500/550 / Re: Relocating or alternative to ignition switch« Last post by DomP on May 14, 2024, 05:27:16 PM »I know where there might be some brackets but they’re in the US. Don't worry Roo, I'll cobble something up on the cheap if I can, failing that I'll take you up on your kind offer mate 95
CB500/550 / Re: What is the correct 500 rear brake light switch wiring route ?« Last post by ozzybud on May 14, 2024, 05:18:23 PM »Here is my unmolested CB550. Plugs in behind the frame bar
96
CB500/550 / What is the correct 500 rear brake light switch wiring route ?« Last post by McCabe-Thiele (Ted) on May 14, 2024, 05:01:40 PM »I can't seem to see the best route for the brake lamp switch wiring here is my photo.
Not sure if this would interfere with the fitting of the side panel. Does anyone have a photo of the correct wiring route? The cable tie is temporary, iginition currently disconnected whilst I'm doing the static timing. .PXL_20240514_154010749 by Macabe Thiele, on Flickr 97
CB500/550 / Re: Relocating or alternative to ignition switch« Last post by Laverdaroo on May 14, 2024, 04:54:22 PM »I know where there might be some brackets but they’re in the US.
Do you want me to ask my pal over there Dom? It’s a bit of a long shot but I know they’re there…… Sent from my iPhone using Tapatalk 98
CB500/550 / Re: Relocating or alternative to ignition switch« Last post by Laverdaroo on May 14, 2024, 04:52:54 PM »Sorry to hear that Bryan, best wishes mate.
Sent from my iPhone using Tapatalk 99
CB500/550 / Re: Relocating or alternative to ignition switch« Last post by DomP on May 14, 2024, 04:42:46 PM »Sorry to hear about your sister Bryan.
I may make up a bracket and utilise the horn fixing points 100
CB350/400 / Re: rotor removal tool. Also Gaskets« Last post by Eldrick on May 14, 2024, 04:27:56 PM »Bike 'broke down' two days ago. Battery was not charging when I went on a run two days ago. It is a new battery and I recently replaced the wiring loom. I can't for sure rule out the rectifier or regulator however the AA man, (a biker too, he used to build custom machies for himself) strongly suggested the issue is insufficient charge from the [/color]alternator. [/size]
|