Recent Posts

Pages: [1] 2 3 ... 10
1
On my original 400/4 I zip tied the box on the top frame tube and just clear of the carb bank as there was just enough room for it to sit between the fuel tank tunnel and the frame tube. I thought I'd had a result until one day when giving the bike a handful it topped out at 110mph🙄, (actually it was about 70!). The CDI box had slowly worked it's way back down the frame just enough to interfere with the top of the carbs at full throttle.
I'm 90% sure the Boyer does use a wasted spark Ash👍
2
Out & About / Re: SOHC meet in Scotland
« Last post by taysidedragon on Today at 01:10:34 PM »
The weather forecasting system is primed and ready!

[ Guests cannot view attachments ]
3
Out & About / Re: SOHC meet in Scotland
« Last post by taysidedragon on Today at 12:32:41 PM »
Apologies I can’t make it after all have been asked to help out at a police Bikesafe event. Next time.👍

No worries 👍
4
CB500/550 / Re: Swinging arm bushes
« Last post by Laverda Dave on Today at 12:28:04 PM »
+1 with the bushes sold by Julie and Ted's top-tip re the freezer. A word of warning though, make 100% sure there is no paint on the edge of the swing arm where the top hat of the bush sits otherwise the swing arm will bind on the frame at the pivot point when you torque the pivot nut.
5
Do you mean this retainer and tool Ted?



If so, I recently bought the tool and an aftermarket retainer from a different supplier and the tool didn’t fit correctly, as you can see. When I contacted them, they checked their stock and found the new batch of retainers didn’t fit the tool but the original Honda retainers did. They sent me a genuine Honda one as a replacement which was fine. I wonder if DSS has the same issue?
6
CB500/550 / Re: Float height 500 k1
« Last post by mickwinf on Today at 12:16:37 PM »
Having similar issues with Lazarus at the moment so have moved the needle to middle groove, haven't tried it out yet as our dog has had an operation so looking after her is taking priority over bikes!
7
CB500/550 / Re: Swinging arm bushes
« Last post by mickwinf on Today at 12:12:56 PM »
I never have much luck sawing the old bushes so made a simple tool. A thick washer the diameter of the hole in the swing arm but too big for Bush. File 2 flats on washer to allow it to pass through Bush then drop through to other side and drive Bush out with long drift. Easy! Also recommend bushes sold by Julie.
8
Misc / Open / Re: long covid
« Last post by McCabe-Thiele (Ted) on Today at 11:37:21 AM »
I don't want to pry do you have some level of COPD that causes you to struggle?
9
Misc / Open / Re: long covid
« Last post by Moorey on Today at 11:24:16 AM »
maybe this isnt the place to post this but it might be of use to someone.  i was diagnosed with long covid recently by my GP after chest xrays, cardio ecg, 24hr ecg and a number of asthma tests but nothing untoward showed up. but they did acknowledge that my breathing capacity was 50% what it should be. so i just accepted that i was stuck with it.  anyway, i mentioned it to a guy a few weeks ago who is very into alternative medicine and a vegan. so i was naturally sceptical!  apparently, his friend had long covid and after some research, started taking a low dose nicotene patch.  it seems that he improved drastically and is now much better. i didnt bother following it up as it seemed a bit fanciful, but my wife suggested i give it a go. so i got a pack of step 3 7mg patches and stuck them on. only four days in, and i realised this morning that my breathing is almost normal!  i'm going to carry on for two weeks and then stop.  however, if you try them and you drop dead, dont blame me.  but if youre getting on a bit like me and struggling with it, give it a go. there is anecdotal evidence on google but nothing science based as yet, but i assume some research is going on.  although i'm still unable to lift my 750-4 engine onto the workbench! but maybe i'm just old...

pete

I do have it and struggle at times with my lungs, I will be interested in how it works out for you over a period of time. We are coming into spring and summer though which does make a big difference for me.
10
CB500/550 / Re: Swinging arm bushes
« Last post by McCabe-Thiele (Ted) on Today at 10:50:50 AM »
I used the bushes that Julie sells in my 400 & 500 - they are spot on.

I put the replacement bushes in the freezer overnight then drited them in with out too much difficulty.

I don't recall any removable inner steel tube, it is shown in the parts book - I obviously left mine as it was.
Pages: [1] 2 3 ... 10
SimplePortal 2.3.5 © 2008-2012, SimplePortal