Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - THUNDERDOWNUNDER

Pages: [1] 2 3 ... 9
1
CB350/400 / Re: fitting of the petrol tap
« on: April 17, 2023, 05:38:14 PM »
Just reading your post on fuel filter repayment and was wondering if you have The dimensions of the big rubber sealing washer as the one I have is crushed to death and I need anew one .

2
Announcements / Re: 400/4 fuelTap Filter .
« on: April 15, 2023, 01:13:28 PM »
Yes still have the old one but it’s very fragile . I think the size is 16 mm x 1,5mm x10 mm . The 10mm is the hole size .

3
Announcements / Re: 400/4 fuelTap Filter .
« on: April 15, 2023, 09:30:23 AM »
I have a new kit but the rubber seal has got lost . I did ask Julie but she says no .

4
Announcements / Re: 400/4 fuelTap Filter .
« on: April 15, 2023, 08:55:25 AM »
Middle washer

5
Announcements / 400/4 fuelTap Filter .
« on: April 15, 2023, 07:30:43 AM »
Hi does anyone know where to get the rubber seal for the Filter assembly without buying the Whole set . Thanks .

6
CB350/400 / Re: 400F rear mudguard options
« on: February 25, 2021, 12:37:51 AM »
I got a front guard Fromm DSS not a bad price I thought. My Australian delivered bike only has three bolt holes standard .

7
CB350/400 / Re: CB350 Handlebars
« on: February 24, 2021, 09:57:07 AM »
I had a look on eBay USA . There where a few sets but the postage as more than the bars . Will have a look on uk site . Nothing here Down Under though ! Anyone have a set in there garage ? They don’t have to be new condition .

8
CB350/400 / Re: CB350 Handlebars
« on: February 24, 2021, 12:57:27 AM »
Thanks , that’s good news I just have to find a set now ! Would anyone know if there are aftermarket bars around as Silvers and CMS say no ?

9
CB350/400 / CB350 Handlebars
« on: February 23, 2021, 12:07:59 PM »
Would  anyone Know if CB350f handlebars will fit my Cb400f ? I am looking for a set but having no luck .DSS has not got any same with CMS . I would consider a good second hand if anyone has a set . Thanks for reading !

10
CB350/400 / Re: 400/4 Regulator rectifier wiring m
« on: February 08, 2021, 12:10:06 AM »
Thanks Sean, those instructions from  DSS left me thinking if I blow this RR up the bike is up for sale . Blown one already and getting flat battery after half an hour . I think the instructions should have been left in Japanese as I have a few friends who cold have translated them better Ha ! Anyway thanks again Bob

11
CB350/400 / Re: 400/4 Regulator rectifier wiring m
« on: February 07, 2021, 12:22:14 PM »
Second page

12
CB350/400 / Re: 400/4 Regulator rectifier wiring m
« on: February 07, 2021, 12:20:53 PM »
DSS Instrucions . Anyone translate please

13
CB350/400 / Re: 400/4 Regulator rectifier wiring m
« on: February 07, 2021, 12:04:43 PM »
Thanks for the info . Instructions came with unit but some one has translated it from Japanese to pigeon English .  The unit on DSS website shows unit with a red/Black wire with two male spade coming off it . The one I received  had a black wire with two spades coming off it . Don’t think it matters what colour the wire is I just need to know where to plug those spades into . The old trgulator still on bike with Green Black White wires coming from harness . Sent DSS email please explain so hopefully I shouldn’ know soon . Thanks again guys and gals

14
CB350/400 / Re: 400/4 Regulator rectifier wiring m
« on: February 07, 2021, 07:57:18 AM »
Thanks for the picture . My new unit from DSS only has the one black wire with two male spades .I would have thought the Five pin Plug for Harness would just plug straight in . That has the 3 yellow 1 green and 1 Red . The extra Black wire with the Two male spades has me FOXED !

15
CB350/400 / Re: 400/4 Regulator rectifier wiring m
« on: February 07, 2021, 05:38:36 AM »
Wow , this must be a hard question to answer . Not o e reply so far after 24 hours !

Pages: [1] 2 3 ... 9
SimplePortal 2.3.5 © 2008-2012, SimplePortal