This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - THUNDERDOWNUNDER
16
« on: February 06, 2021, 10:32:41 AM »
Just bought new combined regRec unit from DSS . Wiring diagram not really clear how to hook up .main plug 3 yellow 1 red I green . Plus 1 BLACK WIRE splits into 2 . Question where do these go ? Thanks if anyone has fitted on recently .
17
« on: November 18, 2020, 07:43:22 AM »
Things are looking up now . Got the newinertube in and the tyre on Speedo Drive graphite grease up tomorrow . Sorry but worm drive is staying in place . Brake disc all shiny and ready for bolting on ..Weekend looking good for a ride . Watch this space !
18
« on: November 17, 2020, 06:21:09 AM »
Well thanks for the info guys . I got the little bugger off with a little help from a Vice and Rubber mallet. Cleaned all the bits in Kero bath . Now has anyone had the worm drive out or is it better to leave alone ? The Oil seal seems OK at the back of the drive so wondering weather to just grease up from there ? The graphite lube is good to know as well ! All this from a flat tyre Ha! Hope to be riding by the weekend fingers crossed .
19
« on: November 16, 2020, 08:50:24 PM »
Great , will get some heat on it later .
20
« on: November 16, 2020, 08:31:08 PM »
Call me stupid but it’s not left hand thread is it ?
21
« on: November 16, 2020, 12:51:49 PM »
Thanks will give it a go tomorrow wish me luck . I will keep you posted !
22
« on: November 16, 2020, 12:17:00 PM »
When I took front wheel off I thought dismantle Speedo Drive and re grease but can’t see how to do it . Took the four bolts holding brake disc out . But that’s as far as I have gone . The spindle bolt wont undo and that seems to hold Speedo dive in place ?
23
« on: November 16, 2020, 05:39:40 AM »
The set of pipes I took off where damaged on outer side and the splitter box has a hole or two. . My bike came with a DSS new exhaust system so I was lucky as he is asking over a grand (Pounds) for them . They are a pig to fit but you get there in the end . Good luck with your podject from WA .
24
« on: November 16, 2020, 05:25:35 AM »
Good morning all , I took my front wheel off to fix a flat tyre and ended up taking the Brake Disk off to clean and paint centre .Well while I was at it I decid to clean up front brake caliper . All that is now done but just wondering if I should grease wheel bearings and grease or Oil up Speedo Drive . I had a go at undoing the Centre bolt but after 45 years I won’t budge . Any ideas guys or should I just leave it alone .ie if it’s not broken leave it alone . Thanks for reading .
25
« on: November 12, 2020, 08:30:47 AM »
News Update . Sleazed up a treat . Used wet and dry with a sprinkling of WD40 . Clean
as a whistle now !
26
« on: November 09, 2020, 11:29:42 AM »
Bugger , you won’t believe it but the bike was in Sydney for over a year . I got fed up with it sitting at my mates place in Blacktown so I put it on Gumtree and sold it to a guy over here in Perth . He paid the shipping so that knocked the price up for him . I have got an Original Four into one set of pipes but they need a bit of braising. . Just put DSS set on my bike . Not as good as the originals but they look good .
27
« on: November 09, 2020, 07:03:13 AM »
Thanks for the info Guys . Will keep you posted on progress !
28
« on: November 09, 2020, 06:57:58 AM »
Pity you don’t live Down Under . I just sold 75 400/4 with Spare engine for 500 quid .. mind you it was all in bits but I think most of it was there !
29
« on: November 08, 2020, 09:20:00 AM »
Some pics of the Job
30
« on: November 08, 2020, 08:03:01 AM »
I would just like them to look better there is minimal scoring and thought may be a clean up on a lathe might be the go but it says on the Disc MIN THK 6 MM and I only have about 7 MM THK now . So better not go down that path !.
Depth 6 MM
|
Show Posts