This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - THUNDERDOWNUNDER
Pages: 1 2 3 [4] 5 6 ... 9
46
« on: December 18, 2019, 11:24:15 AM »
With the Regulator bolted to frame what is the colour from Top to Bottom do the three wires from Loom go Thanks ?
47
« on: December 17, 2019, 11:35:52 AM »
Yep it seems strange that all seems to be be working ok even the reg/rec is only letting current one way . I have put on a new loom DSS and a new connecting short loom from altinator to proper loom if that makes sense ? The reg/rec has no wires to the regulator that is still on the bike but the new wiring loom does have wires to it . So should I connect said wires to old regulator or not ? I will give old connectors a clean and keep my fingers crossed .
48
« on: December 17, 2019, 02:48:54 AM »
Pics
49
« on: December 17, 2019, 02:47:45 AM »
Pics I forgot
50
« on: December 17, 2019, 02:45:25 AM »
Thanks didn’t want to blow up my multimeter . All yellow wires tested 15/16 volts at 1000 rpm . It was even higher at 4000 rpm something like 24 volts . Just tested reg/rectifier . Diodes seem ok all around 500 one way only . It’s a second hand unit which came on the bike . It says 12 Volt Reg/Rec SH538-12-5.7 SHINDENGEN JAPAN . Someone has written in Pen 85 VT 250 INTEGRA . Wondering if that’s the problem ?
51
« on: December 17, 2019, 01:06:03 AM »
How do I use multimeter to test A/C voltage out of yellow wires ? There are two prongs from meter one positive one negative . Does one go to ground ?
52
« on: December 15, 2019, 04:41:53 AM »
Checked out field coil and stator all see OK . Wish it would cool down here !
53
« on: December 14, 2019, 08:47:48 AM »
Way tooo Hot to work on bike today 41 degrees in the shade . Thinks it’s a strip down job coming up !
54
« on: December 13, 2019, 04:17:58 AM »
Hopefully will find the problem soon .Thanks for all your help !
55
« on: December 13, 2019, 02:05:21 AM »
My kick start on 400/4 slips off the splines if used to much . I did see someone say put a self tapper in between splines and knuckle ?
56
« on: December 13, 2019, 02:01:44 AM »
Tested again this morning .Earthed the green this time . Still the same no magnetic pick up from casing . Will have to test field cool next Any one know the best way to tackle it ? Ay even just a busted wire .
57
« on: December 12, 2019, 11:56:54 AM »
Thanks , I will give it a go in the morning .There doesn’t seem to be any damage to The casing but it is old being 1975 .
58
« on: December 12, 2019, 05:33:41 AM »
Just a thought the wires from regulator to field coil are brand new as the old ones where broken and fragile so I got a replacement harness from DSS . So if that’s the case maybe it’s the field coil playing up ?
59
« on: December 12, 2019, 04:43:04 AM »
Opps sprocket word gives it way .
60
« on: December 12, 2019, 04:38:48 AM »
Is the sprocket cover the altinator cover ?
Pages: 1 2 3 [4] 5 6 ... 9
|
Show Posts