This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - THUNDERDOWNUNDER
Pages: 1 ... 3 4 [5] 6 7 ... 9
61
« on: December 12, 2019, 02:03:43 AM »
Connected black and white wires from regulator . Started engine and couldn’t see a spark and feeler gauge would not hold to generator cover .
62
« on: December 11, 2019, 09:46:57 AM »
Strange how the 400/4 parts are so rare I bought a whole bike last year for 150 and it had a spare engine with it . Must have been my lucky day
63
« on: December 11, 2019, 06:56:33 AM »
With ignition off battery reading was 12.77 volts .Then meter red to Black on regulator wire With ignition on I got 12.49 volts .I then joined black to white regulator wires and ran engine to 4000 revs only getting 12.39 volts not increasing!
64
« on: December 11, 2019, 06:41:08 AM »
Yep the 350 fourfits . I bought one last year and it works fine . I also bought a set of clocks of 350 four with only 50 miles on them .The Red line starts a bit early but I can live with that !
65
« on: December 09, 2019, 10:28:58 AM »
Back now . Tested as recommended . Wires off regulator . ignition on . test came out at 0.07 volts Battery was 13.10 volts . That was testing black wire only Black wire from multimeter to black wire from regulator and red wire from multimeter .
to positive on battery .
66
« on: November 26, 2019, 03:18:58 AM »
Great stuff thanks for the help !
67
« on: November 26, 2019, 12:13:48 AM »
Thanks BryanJ I will give it a go latter today if I can get a chance . I will be away for the next week so will get back to you as soon as . Rob .
68
« on: November 24, 2019, 11:53:29 AM »
With the battery loosing power over night where is the short ?
69
« on: November 24, 2019, 11:17:22 AM »
The battery is only a few months old . So don’t think it’s that . When I bought the bike a few years ago the owner said there was a short somewhere . I have put a new wiring loom on . So it’s down to the generator or regulator/ rectifier
70
« on: November 24, 2019, 09:36:37 AM »
At 4000 rpm it’s readin 12.41. At tic over it’s 12.34 .
71
« on: November 24, 2019, 05:22:25 AM »
Sounds encouraging and thanks for the info I am going to need !
72
« on: November 24, 2019, 05:01:12 AM »
Ideas needed for fix . At the moment I have to charge my battery off the bike . Fully Charged it lasts about Half an hour . Starts on the button then looses power fast no starter and indicators stop . If I fully charge and leave it over night it drains . So what’s wrong Guys ?
73
« on: November 03, 2019, 06:48:35 AM »
Problem fixed .slight lip on collector box inlets . Looked like build op of Crome platting . Filed it flush . Just have to assemble them now Agh !
74
« on: October 27, 2019, 11:27:32 PM »
Just another thought on this . Why is there only one retaining clamp on the collector box ?
75
« on: October 27, 2019, 11:44:44 AM »
Funny you should say that . I will try a socket on it tomorrow for roundness . If all ok will get the dremel out or lots of elbow grease with the emery paper ! Thanks for all the input guys !
Pages: 1 ... 3 4 [5] 6 7 ... 9
|
Show Posts