This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - robvangulik
Pages: 1 2 3 [4] 5 6 ... 15
46
« on: August 01, 2022, 11:15:04 PM »
Maybe this site could be helpful http://cycle-ergo.com/According to them the 400 is 30" high and the 500 31.7"
47
« on: July 10, 2022, 06:30:27 PM »
Those dowels are there to make sure the top and bottom cases are perfectly lined up, because especially the crank bearings are measured with thousands of an inch (or mm), so what do you think happens when you screw those cases together without dowels?
48
« on: June 13, 2022, 02:55:03 PM »
Like Ted said, hold the complete wheel under water and it WILL show where it leaks!
Even a very small inflatable childs swimming pool works, and doesn't cost you any real money.
49
« on: March 24, 2022, 09:31:19 PM »
I know, but now I stole it with permission 
50
« on: March 23, 2022, 05:38:32 PM »
Excellent, may I use this wonderful explanation on our (Dutch) board when asked the right questions?
51
« on: March 19, 2022, 01:13:15 PM »
Me neither
I clicked on your name, goes to profile then click on envelope, which takes me to a dialogue box for email, then pressed Send. 
Click on "send PM" and ask for email....
52
« on: November 23, 2021, 11:55:26 PM »
Hallo Ruben, nice to see yet another fellow countryman here, as mentioned before very nice people and a lot of knowledge to be found here. But did you know there is also an excellent Dutch club dedicated to these bikes? Also very nice people, etcetera, and with activities a bit closer to home  , for instance a yearly clubcampingweekend. Do try www.cbfourclub.nl and maybe become a member there too?
53
« on: October 11, 2021, 10:44:27 PM »
I've been there, far too long ago, should have a bunch of photo's somewhere.
Beautiful roads!
54
« on: October 07, 2021, 10:42:20 AM »
Yep, been to the dealership, £30 a set of six. Dick Turpin was hung in York
And what's the price of a side panel?
55
« on: October 06, 2021, 10:46:24 PM »
They are still widely available partnr. 83551 300 000 , cmsnl sells them from €1 to €3,50 for over 7000 models in several sizes, they fit on my '75 cb400f and my '87 CBR1000F and lots of other models from 125 to 1100cc.
56
« on: September 25, 2021, 07:09:25 PM »
Looks alright, just doesn't sound right somehow....
57
« on: September 09, 2021, 07:41:26 PM »
The old ones lasted for almost half a century, when the new ones do the same, what's the problem?
58
« on: July 29, 2021, 08:52:09 AM »
I did just that in the 80's for my 836, worked fine, and am busy making one for my 54mm "big bore"  400f, I have never seen them for sale, where do you get them?
59
« on: July 28, 2021, 12:28:37 PM »
Well im in warrington right now and its persisting down
Don't despair, across the Channel it's been the same, if not worse for the last week! 
60
« on: July 25, 2021, 05:00:14 PM »
No sprockets without teeth? The chain hasn't come off the rear sprocket? Does the clutch lever feel different?
Pages: 1 2 3 [4] 5 6 ... 15
|
Show Posts