This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Laverda Dave
Pages: 1 ... 165 166 [167] 168 169 ... 171
2491
« on: August 16, 2016, 10:38:25 PM »
No Trigger, not Wolverton, it was in London.
2492
« on: August 16, 2016, 05:44:58 PM »
Thanks Chris that's a helpful link especially about the throttle screw.
2493
« on: August 16, 2016, 04:47:04 PM »
 £2k to fill the tank with acid! Maybe I could try a washing up bowl full of coke!! Back in the day when I worked in a train overhaul works I had access to that sort of cleaning kit, and blasters, stove enamelling, zinc and chrome plating, not anymore, those days have well and truly passed 
2494
« on: August 16, 2016, 01:43:08 PM »
I have set my carb floats using the Haynes method although I haven't yet started the bike. Is there another secret method I should be using?
Dave
2495
« on: August 16, 2016, 01:37:08 PM »
Lovely finish there Trigger.
My next project after 'project 400' is the restoration of my Rickman CR750 and it's festering engine. I'll try your method to clean it up.
Dave
2496
« on: August 15, 2016, 11:13:02 PM »
I had my castings vapour blasted for the same reason, i couldn't clean them up even by soaking in paraffin and when that failed, using a dishwasher tablet in boiling hot water for a couple of days (someone told me it would work....!).
After I got the blasted cases back I cleaned them three times with gunk and boiling hot water and then a final 80psi air blast.
2497
« on: August 13, 2016, 12:07:30 PM »
Thank you both, very helpful and going out to set the carbs now.
The adjustment tool is the same on both sites. The M&P item is £4 cheaper. I have one on order.
Dave
2498
« on: August 10, 2016, 10:31:36 AM »
Hi All.
I have fully rebuilt the carbs with an ultrasonic clean and vapour blasting. I have installed new jets an re-platted and polished the parts that needed it.
Having re-assembled everything does anyone know of the base settings I should be using in order to start the bike? The manual gives the range of the idle screw settings but is there also a setting for the balance adjusters to start from? I have presently screwed all mine right down. I have checked the on-line shop set up manual for clues with no joy.
Does anyone know where the 'special' tool can be bought from that allows the balance nut to be undone and the centre screw to be turned at the same time? I remember this was a Honda special tool years ago.
Any help would be appreciated.
Dave
2499
« on: August 05, 2016, 06:36:03 PM »
Once again, what a great site this is:-).
Trigger, thank you for looking and your reply.
Piki, Thank you and PM sent.
2500
« on: August 03, 2016, 10:44:49 PM »
I bought a set from M&P, they are pattern parts though so if you want to keep it original use the Ash repair guide. Just for info though, there was a previous thread on here about making sure pattern coils have a 4-ohm resistance if using electronic ignition systems as a number of pattern coils sold on e-bay are 2-ohm and will cause damage to the ignition system. M&P told me their coils were 4-ohm, when I received them I checked to be on the safe side as I have a brand new Boyer system to go in 'project 400/4' and they were as described, happy days  Dave
2501
« on: August 03, 2016, 10:32:19 PM »
Do you have another one please Trigger! I had one on order from DS, they were getting a pattern one from the US but called me today to advise there are no more available and they have no plans to manufacture anymore in the near or distant future  . The one I have on 'Project 400/4' is cracked and has two broken lugs, the clocks are now fully restored and need a decent console to fit between them! Happy to pay, I don't expect a freebie Dave
2502
« on: August 01, 2016, 03:29:32 PM »
I have a Cibie unit without the adaptor ring, the person before me had used bathroom mastic to fit it into the rim  There was a rough s/h unit on e-bay last week with the reflector chrome going rusty, I only wanted the adaptor ring and even that was rusty!, I was outbid, it sold for about 15 pounds . The one on e-bay at the moment is being sold by bike pusher, he sold one similar a few weeks ago, I gave up when the bidding reached 40 pounds on that one and this one is likely to go the same way. I have today ordered a DS unit for 29 pounds, it has an H4 bulb so good enough. I'll keep the Cibie in case an adaptor ring turns up at a good price.
2503
« on: July 31, 2016, 11:58:08 AM »
You can try Bill Bailey at Swallow motorcycles in Eastcote, Middlesex. I've known him for 20+ years and he's old school when it comes to bikes, if he says he's going to do something he does it. 100% recommended.
2504
« on: July 31, 2016, 11:51:04 AM »
I fitted Hagons to my original 400 and replaced them within 6 months, too hard, great on the 350 Morini though  I have bought a pair of TEC's for the 400 project, good price and really nice finish with good reports of handling. Good enough for me Dave
2505
« on: July 12, 2016, 11:01:18 PM »
Welcome to a great forum, fantastic people on here, you'll enjoy it. Good luck with the projects, start with the 400 
Pages: 1 ... 165 166 [167] 168 169 ... 171
|
Show Posts