This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Golfcarmad
31
« on: April 26, 2019, 02:56:28 PM »
Comstars fitted.1.85 x 18. Must admit rode back round block when delivered.no noticeable problem.bought it to do complete rebuild.thanks for measurements.if cannot sort at Stafford etc will take long one and cut down to your measurement. Thanks
32
« on: April 26, 2019, 02:47:25 PM »
Only have wheel n spacers that came with bike which was running before strip down! Weird??
33
« on: April 26, 2019, 02:19:06 PM »
When trying to fit the 2 spacers on rear wheel I am having to crow bar with excessive force to fit wheel. My bike is an f2 now fitted with f1 swinging arm.can anyone advise if spacers are different in length on the 2 models?? My spacers are 28mm and 44mm in length. It is possible mine is USA import due to wiring which has been much closer to us wiring diagram in Haynes. Cheers Paul
34
« on: March 31, 2019, 05:42:34 PM »
Sorted,thanks again.xx
35
« on: March 31, 2019, 04:44:29 PM »
Thanks that really helps.i had bent the spring completely out of shape. Nearly there!! Thanks as always.
36
« on: March 31, 2019, 03:08:55 PM »
Hi guys n gals,I cannot figure out how large brake spring fits.i think I must have bent it when removing.hoping someone has pic I can follow.thanks Paul
37
« on: March 20, 2019, 04:52:30 PM »
Thanks what sizes did you choose could you have gone wider.
38
« on: March 20, 2019, 04:33:47 PM »
Hi
Today she ran for first time.all seems well.i have comstars(for now) which I quite like.need tyres.read some old posts,thought I would ask current opinion.my rims are F: 1.85x19. R:1.85x18
All opinions appreciated.stickiness and ride ability more important than original looking.thanks Paul
39
« on: March 08, 2019, 03:47:12 PM »
Thanks again x
40
« on: March 08, 2019, 10:05:30 AM »
Hi, my carb has the 4 breather tubes at bottom of carbs.pipe to tank for fuel,what are the 2 long tubes at top of carbs for? Just breather tubes?
Thanks
Paul
41
« on: February 26, 2019, 09:43:13 PM »
Just attached to check engine turned over-which it does.
42
« on: February 26, 2019, 09:26:32 PM »
Latest photo
43
« on: February 26, 2019, 09:21:19 PM »
Hello 1 x idiot here,I had put the washer onto the rear axle under the castellated nut!!!
Thank you,about to put oil and start engine inside conservatory-a bit late tonight maybe.
Apologies
paul
44
« on: February 26, 2019, 08:55:28 PM »
Hi again,I am refitting the correct oil filter case to the engine.i have: bolt complete with o ring inside bolt appears to be a cylinder,spring held in place by a through pin.i have the outer casing,a new filter which has a rubber seal at each end.and finally a large diameter spring .thats it!that is what was fitted.what if anything am I missing please?
45
« on: February 26, 2019, 04:50:57 PM »
Thanks,1mm or so I can sort,picture in Haynes looks more like - 40mm,so thank you for advice.
I do have old filter,nothing stuck,but I wwill go through "parts over so far" box and check.
Regards
Paul
|
Show Posts