This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - yozzer74
Pages: 1 2 3 [4] 5 6 ... 45
46
« on: June 20, 2018, 08:56:48 PM »
K2 tried covering the filters didn't make any difference .but when I covered them up about 80% was worse .I've not checked with timing light I've got one on order .it does have electronic ignition with a ignitor box .bike is a 1982 model
47
« on: June 20, 2018, 08:33:01 PM »
Hi long shot this question. My gs550 is running really bad I've fitted k&n pod filters custom 4 into 2 pipe .Bike as c.v carbs dyno jet stage 3 kit fitted .problem is bike ticks over nice first part of throttle is good .When stood revs all way to red line .but when under load doesn't want to rev and pops and bangs bogs down .I've tried lifting needles up bigger main jets but makes no difference at all.im thinking it could be a timing issues. Anyone got any ideas I'm a little stuck .Cheers yozzzer
48
« on: June 13, 2018, 05:29:06 PM »
He's taking it over next week Steve told him not to start it again till he's over there with
49
« on: June 03, 2018, 06:45:43 PM »
I've ordered this one not cheap but as good reviews. Plus you can clean it out
50
« on: June 02, 2018, 09:19:10 PM »
Hi can anyone recommend a decent inline fuel filter. With a good flow rate that's not too big.cheers
51
« on: May 14, 2018, 08:46:33 PM »
Yes when he cleaned them up he found that they had been filled with some kind of silicone.they don't leak so I can live with it .
52
« on: May 14, 2018, 08:04:00 PM »
Got my carbs back for GS .done by Harper's top job again .
53
« on: May 14, 2018, 07:57:17 PM »
Not yet mark it's my mates bike and he's away at minute
54
« on: May 12, 2018, 05:47:44 PM »
Nice looking bike .I can agree with royhall the parts are eye watering bout ,two inlet rubbers for my gs550 yesterday 80 quid ooch
55
« on: May 12, 2018, 04:19:40 PM »
Hi looking for some help been trying to bleed my breaks on GS I'm building .but can't get the leaver to firm up .it's got new break lines rebuilt calipers also using a front master cylinder from a gsxr 1000.could this be the issue?? There's no more air coming out of calipers now . [ Guests cannot view attachments ]
56
« on: May 01, 2018, 08:14:27 PM »
I got one of those pipes from carpys.fit is quite poor on them .did sound nice though.i have had a pipe for my new build made . which was around the same price .but fits great and made out of stainless.
57
« on: May 01, 2018, 03:37:54 PM »
What about a 400 four tank they fit straight on or cx 500 they look good on the 750
58
« on: April 29, 2018, 05:28:43 PM »
Cheers mark will give it a check
59
« on: April 28, 2018, 07:46:41 PM »
K2 that was first thing we checked .yeah plenty of oil .will take a look at carbs .
60
« on: April 28, 2018, 04:30:09 PM »
Nope it stays there when clutch pulled in
Pages: 1 2 3 [4] 5 6 ... 45
|
Show Posts