Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - rosco

Pages: [1]
1
CB350/400 / project or spares
« on: April 12, 2021, 08:10:27 PM »
If anybody is interested in a project or spares for a cb4000f  On Facebook Marketplace  Type in search honda cb400f project Then look through  For a full bike less carbs and fuel tank  asking £650  I cannot cut paste thingy me bob( Technophobe ) Sorry Just thought someone may be interested  Cheers Ross

2
Where's My Old Bike? / looking for old bike
« on: February 12, 2021, 09:20:09 PM »
 Hi i am looking for my mate,  his old bike from the 60s    The bike in question is a Honda C92  125cc Benly  1963 or 1964 Reg number is   AVY 533 A or B   colour was Blue  The bike was registered by Alan Mountains in York  the last known owner was Raymond Gowlett of Catterton nr York   Any information greatly received   It does not show on .gov website  Hope you can help    Cheers  Ross

3
Recommended Sources for Parts and Services / welding
« on: May 17, 2020, 07:35:55 PM »
If anybody requires any, i mean any sort of welding  even fuel tanks  PM me and i will pass on details of my mate who has his own engineers shop set up in his garage, welding , turning ,bending ,rolling  making  He will have a go at anything and he is very very good  If he cant do it, he won't attempt it  He has done loads for me and other members  Don't waste money buying new Repair and keep it original   Sorry this sounds like an advert But I'm only trying to help members Thanks Ross

4
Other Bikes / Pistons
« on: May 11, 2020, 03:43:54 PM »
I was looking for pistons for a C77 When i found this site   IMD Pistons in Cheshire  Has anybody dealt with them If so what's the quality like   Price wise they look very good  A pair of pistons +rings +pins + clips @£109:99  Compared with DSS @ £171 Looking forward to your comments    Ross

5
CB350/400 / genuine parts
« on: February 05, 2020, 12:35:14 PM »
Hi All   i have just bought some carb clamps to airbox (4 ) for my cb400 f2 they are Black in colour  They are marked as genuine parts   But another label states Made In India   My question is pre 1978 did Honda source supplies from either China  Taiwan or India  The guy i bought these from is adamant they are genuine  But my thoughts were back in the day all parts were Made In Japan I don't Know if modern type bikes are using foreign sorted parts ???  All your thoughts appreciated   Cheers  Ross

6
CB350/400 / Carb inlet manifold rubbers
« on: November 27, 2019, 04:27:59 PM »
Just got my inlet rubbers back from Ash who has softened them Now I've come to fit them and noticed there are two different types ( didnt notice when taking them off  DOH ) Two marked 1&4 Two marked 2&3 Obviously to fit each cylinder   Question is are the numbers fitted uppermost on the corresponding cylinder  IE  cylinder No 1   mark 1 to top  mark 4 bottom  cylinder No2 2 to top  3  to bottom  ETC   Ive searched all service manuals and nothing on removing / refitting  Cheers Ross

7
CB350/400 / carburettors
« on: November 02, 2019, 10:38:59 AM »
Carburettors back from Gerben and they look brilliant Photos do not do justice They do look brand new  Just got to fit them and get it started Fingers crossed

8
CB350/400 / rear sprocket
« on: July 27, 2019, 12:57:01 PM »
Just fitting a new rear  sprocket and it seems a lot of play Not much rotational just a little bit of movement within the bolt holes of the sprocket The bushings seem ok But lateral play there is at least 1/8" old money Is this the norm ???    Also the rear spindle The PO has put it with the nut on the sprocket side Looking in the parts catalogue thats right   Yet in the service manual shows nut on brake side which i believe to be correct Your thoughts appreciated Cheers Ross

9
CB350/400 / oil seals
« on: July 10, 2019, 03:55:03 PM »
Engine rebuild coming on fine, after Head rebuild and rebore by Trigger.  Just one problem I didn't fit the right hand crank seal before bolting the cases back together. I now not sure which way it fits. Logic says looking at it , the metal side out. Is this correct ?
Thanks Ross

10
Other Bikes / c77/ca77
« on: May 26, 2019, 08:38:42 PM »
Hi Guys and Gals  Don't want to turn this into a shop But having a clear out and have loads of parts for Honda 305cc C77/CA77/CB77 and wanted to give peeps on the forum a chance before they go on fleabay. Frame, Turtle fuel tank,Engine parts etc etc Please contact through messages  Cheers Ross

11
CB350/400 / machining
« on: May 15, 2019, 09:59:38 PM »
 Hi  Is there anybody on here that does rebores and head work  As will require this service on my 400/4  Ross

12
CB350/400 / f2 colours
« on: May 15, 2019, 06:46:07 PM »
Hi Im sure i will be put right   My 1978 f2 400/4 is in Light Ruby Red    Is this the correct colour for this model   as i have only seen f2 in   
Candy Antares Red or Parakeet Yellow with tank stripes  Has there been a crossover between these models  Thanks

13
New Member Introductions / newbie
« on: May 15, 2019, 11:42:17 AM »
Hi All  Newbie signing in Ross from Tadcaster Brother of Heliwilly [BillW] Bikes 1978 CB400/4 f2 { sorry yet another 400/4 } 1966 CA77 305

Pages: [1]
SimplePortal 2.3.5 © 2008-2012, SimplePortal