This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Erny
Pages: 1 ... 3 4 [5] 6 7 ... 33
61
« on: February 25, 2022, 09:38:31 AM »
62
« on: February 25, 2022, 12:59:39 AM »
yes, but if it is the same, why the hell Honda does not show it is?
Honda would either use 374 code for 390 model or says 390 parts supersedes 374 one... but this is not the case.
63
« on: February 25, 2022, 12:22:58 AM »
64
« on: February 25, 2022, 12:16:33 AM »
so, simply buy 17210-390-P00 ?
I did not find any compatibility with 17210-374-P00 or 17210-374-003..
But would be great if it fits!
65
« on: February 24, 2022, 11:33:15 PM »
Hi all, I have CB550K1 (type 374) import from US that has rather specific (in Europe) airbox and also air filter. Part diagram for my CB550K1 US model : https://www.cmsnl.com/honda-cb550-k1-four-1975-usa_model466/partslist/F++05.html#.YhgS0eiZOMoIt is difficult and expensive too to get new filter. Genuine very hard to find (and expensive) and alternative/repro too. CMS does not have them anymore. So, I start to consider changing whole airbox to other type (European?) that will solve this problem... Does anybody have good overview what is the "best" option to look at? I mean what airbox(airbox housing)/filter I should be serching for? Thanks for your ideas
66
« on: February 24, 2022, 08:09:02 PM »
Update from my side:
Rings ready for shipping.
final price for 1 ring : 6,90 EUR
shipping (traceable letter) : 4,90 EUR
you can pay me PP or bank transfer (EUR)
Oddjob - qty5 (pls PMme shipping address)
Sesman - qty2
mickwinf - qty2
ebmbiker - qty1 (pls PMme shipping address)
I still have 3 rnigs more available, if someone is interested let me know
67
« on: February 21, 2022, 03:26:28 PM »
John, hard to believe, but I spent 7.5mls (!) from that place (Suckley) whole summer back in 1994 on the farm, picking strawberries, cherries, apples... It was great time, as university student that time, with group of friends.. World is so small 
68
« on: February 19, 2022, 10:30:13 PM »
D rings arrived.
I can start shipping them.
Please send me PM with your address
69
« on: February 18, 2022, 10:06:14 AM »
Thanks!
70
« on: February 17, 2022, 02:30:41 PM »
So nobody else to comment / confirm proper order of installation?
71
« on: February 17, 2022, 02:29:50 PM »
OK, I increased order by 1pc for you
72
« on: February 16, 2022, 10:05:34 AM »
Seems that cost/pc will be likely about 7eur, hope still OK for you. They charge based on real material consumption. If not let me know, I can still adjust order qty
I count on:
- Oddjob qty5
- Sesman qty2
- mickwinf qty2
73
« on: February 15, 2022, 11:06:14 PM »
OK, tomorrow, I'll try to confirm it, ~10 more for you in total.
Untraceable envelope to UK is up to 2 euro, traceable up to 5 euro.
Keep ypu informed
If still someone else interesed, let me know till tomorrow morning 7.30AM UK time
74
« on: February 15, 2022, 10:10:00 PM »
OK, but when first goes left one (retainer side), before driving it in both spacers must go in as first. This is the only way to insert longer spacer. This looks to me bit unlogical.
Maybe somebody else can confirm it?
75
« on: February 15, 2022, 09:23:51 PM »
Just online from garage: I'm in front of rear wheel assembly and wondering what side first? Logically I would first install right one (brake side), until fully seated. Then from opposite side long spacer, short spacer and left bearing until it touches spacers. Then tightening retainer while checking for free rotation of bearings?
Please correct if wrong
PS: normally I would not ask and do as above, just seen some posts on US forum instructing other way?
Pages: 1 ... 3 4 [5] 6 7 ... 33
|
Show Posts