1
CB350/400 / Re: Ignition Advance Bolt Torque
« on: September 10, 2020, 08:36:36 AM »
Thanks so much Bryan! That makes a lot more sense!
Try our new info resource - "Aladdin's Cave" (Main menu)
Just added a separate link to Ash's Dropbox thread (shortcut)
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
1
CB350/400 / Re: Ignition Advance Bolt Torque« on: September 10, 2020, 08:36:36 AM »
Thanks so much Bryan! That makes a lot more sense!
2
CB350/400 / Ignition Advance Bolt Torque« on: September 09, 2020, 10:25:06 PM »
Hi everyone. First of all, sorry that the last time I posted was 2014! Safe to say a lot has happened since then!
Still, I've got the 400/4 and have found a renewed desire to get it all up and running again. The frame, suspension and brakes are all done having had a lot of TLC! The engine is also nearly complete (after a complete strip down too) which leads me to ask a question! I'm installing the ignition at the moment and am a bit confused by the Haynes manual. Does anybody know if there is a specific torque for the long retaining bolt in the centre of the assembly (bolts into the threaded hole in the end of the crank)? I thought it was referred to as Cam Retaining Bolt in the Haynes manual so tightened it and it sheared! Now, I'm not sure it needs to be that tight, just nipped up firmly but having spent the best part of a night worrying about getting the sheared stud out, then spending about an hour and using several extraction methods to get it back out (successfully in the end!) I don't want to make the same mistake! Any guidance greatly appreciated. I hope everyone is keeping safe. Thanks all. Regards, Tom 3
New Member Introductions / Re: Hi from Sheffield, pretty new to Honda's!« on: June 17, 2014, 10:08:30 PM »hi tom, im a newbie as well! with a cb400f-2, and only 18k, with all the old mots, recent purchase,youre in good company here, i like the tank cover, try and check inside the petrol tank to make sure alls well!, are you keeping the rear rack?, as im after one!. good luck.honstan3. and as arnie once said on a beach, oil me back!, cheers. Hi honstan3, I'm not planning on using it. I've no idea what it's worth and it's not what you would call "mint" so you're welcome to it if you want it! 4
New Member Introductions / Re: Hi from Sheffield, pretty new to Honda's!« on: June 17, 2014, 10:01:02 PM »Hi Tom, Hi Paul, I've got a feeling your location will be really helpful! I live near Catcliffe, on the new estate at Waverley, right by the Advanced Manufacturing Park. No questions yet, though I've just taken the carbs off for a good clean...damn those things are complicated!! 5
New Member Introductions / Re: Hi from Sheffield, pretty new to Honda's!« on: June 06, 2014, 02:48:33 PM »Hi Tom. Hi Steve, thanks for the heads up on the fork seals as well as the confirmation on the fuel. I assume you mean the oil seal rather than the dust seal? What are the calipers made from? Is it steel or aluminium? Good point. Master cylinder will likely be gummed up too. I used the genuine part from DSS to replace the piston and all seals/clips. Indeed! The front brake doesn't work at the moment (there's fluid in the master cylinder but no pressure at all from the lever). I think the bleed nipple is seized and generally the system needs some attention. This forum is great for advice! I'll have it up and running in no time! Tom 6
New Member Introductions / Re: Hi from Sheffield, pretty new to Honda's!« on: June 06, 2014, 02:41:05 PM »Hi Tom and welcome. Hi Tom. Thanks for the message, thats really helpful. Given it's so easy (I'll quote you on that by the way!!) to access then you're right, its worth an inspection before first start up. I do know that the bike was very well cared for mechanically and rarely driven hard. Up until the late 80's it was serviced in line with the handbook and my uncle (who's bike it was) is no Guy Martin!! Here's a picture from when I picked it up on Tuesday (surrounded by 1920's Morgan bodywork!): Thanks, Tom 7
New Member Introductions / Hi from Sheffield, pretty new to Honda's!« on: June 06, 2014, 10:52:51 AM »
Hi all,
Just an introduction email with some questions on it too! I've recently inherited a Honda 400f Super Sports. Its the F model (registered in June 1976) with just over 22,000 on the clock. It's been buried in a lock up in Chelmsford for the past 27 years and still has a 1987 tax disk! The engine has been filled with flushing oil and the clutch plate has been held off at the handlebar to prevent it seizing. I've got a few plans for it (not sure whether to do a custom job on it or restore it) but first things first I need to check that the engine still runs. All the electrics work (apart from the horn) and it sounds sweet when I kick the engine over. The plan is to change the oil and filter, plug up a new battery, put in some fresh petrol, check for sparks on all cylinders and hope for the best! Should I also look at replacing the cam chain tensioner too? I know these are a weak spot but is the engine an interference engine or not and after 22,000 odd miles, is it going to need doing? Another question, is it OK on modern unleaded petrol? Thanks for your help in advance. I'm a keen motorist (also have a 1991 Porsche 944 3.0 S2 which I regularly grace the relevant forums with questions about!) and have ridden bikes before so I'm looking forward to working on this! All the best, Tom.
Pages: [1]
|