This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - cb750stu
32
« on: November 15, 2012, 08:42:55 AM »
Hi Folks im wanting to tidy up my airbox its a bit scruffy and faded,
What would be the best way to paint it do i need special paint /primer etc ??
Regards
Stuart
33
« on: November 04, 2012, 11:10:09 AM »
Hi Folks, I started servicing and was going to rebuild my rear brake last night and found this As you can see its in a poor state,how do i get the rod and gubbings out ?? Also if i buy the rebuild kit from DS does it replace all the bits i need ?? The rod does move up and down and there is pressure there aswell in the cylinder , Regards Stu
34
« on: October 30, 2012, 09:00:42 PM »
Hi Folks just recieved my new exhaust today and its bare steel,
I was wondering if anyone knows of a good company that does ceramic coating ??
I have had a exhaust done when i had my Westfield but cant remember who did it.
Regards,Stuart
35
« on: October 29, 2012, 07:38:19 PM »
Hi Folks does anyone know can i get paint cans shipped from the States or is it banned ??
Regards
Stuart
36
« on: October 09, 2012, 04:49:39 PM »
Hi Folks just wondering my engine is going to be sitting for a while with no oil in her whilst i do everything else that needs to be done, Will it be ok with no oil in it or is there something i should do to stop any kind of corrosion Regards Stu
37
« on: October 08, 2012, 11:45:40 AM »
Hi Folks, Just wondering do i need the clutch switch to make everything run right ?? My switch wire has snapped where it goes into the lever housing leaving a white plastic piece inside,how does this come out Just wondering, Stu !!!
39
« on: October 05, 2012, 06:56:58 PM »
Hi folks I'm going need to replace my oil pan gasket as it is leaking. I have noticed that there is some kind of orange rubbery material dotted around the seal ? My Q is should I just put the new gasket on without sealant or use sealant I know gaskets are designed to go on without sealant !!! It will also be a good chance to check the oil strainer !!! Anybody know what torque setting I should use for the bolts Regards, Stu
40
« on: September 30, 2012, 08:21:07 PM »
Hi Folks, I was wondering if anyone has a pic of a vin plate that should go on a 76 750 F1 SS the company that blasted my frame has lost it i should have taken it off but hey ho !! They cant find it probably swept up with all the rubbish after blasting it off my frame !!! I have found this company they have a few to choose from but cant remember what my one looked like ?? http://www.vin-plate.co.uk/motorcycle_plates.htmlRegards Stu
41
« on: September 27, 2012, 09:32:49 PM »
Hi Folks, Just thought i would put up this link to Joker Machine hes in the States very nice guy to deal with i bought a shed load of stuff for my Harley,good returns policy all machine made to order maybe not cheap but fantastic quality, Probably not everyones cup of tea but i am a tart when it comes to "Bling" http://www.jokermachine.com/onlinecatalogcafe2004.asp
42
« on: September 24, 2012, 10:29:33 AM »
Hi Folks my forks have some quite bad scratches and gouges on the fork bottoms just wondering if i can fill these with some kind of filler then sand smooth ?? These will be getting painted eventually does anyone know of a good filler ?? I have heard of Metal Set is this any good !!!
Regards Stu
43
« on: September 19, 2012, 08:59:17 PM »
Hi Folks i am wanting to get my carbs Ultrasonic cleaning stripped and rebuilt with all new kit inside and out can anyone recommened me anyone who does this ??
Regards
Stu
44
« on: September 18, 2012, 04:10:05 PM »
Hi Folks just wondering if a 19" rim with the same width as standard would fit, my frame and swingarm are away getting blasted so i cant compare front and back wheels to check for fitment,
Regards Stu
45
« on: September 17, 2012, 08:48:28 PM »
Hi Folks anybody know where i can get some for my 76 F1 SS
Cheers
|