This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - andeks
1
« on: April 27, 2021, 01:15:19 PM »
Hi All, Trying to buy 4 'o' ring oil seals for bottom of barrels, fits over cylinders. Tried Silvers but cant find them. Anyone help please. Thanks
2
« on: February 17, 2019, 07:09:36 PM »
Thanks everyone, all good advice just not looking forward to doing the deed My barrels look a bit of a mess, any ideas on the best way to clean them up or should they be sprayed with the paint i've done the crankcases in. Also one of the fins is missing a bit, is that aluminium filler ok to build it up. Thanks Dek
3
« on: February 15, 2019, 08:10:34 PM »
Hi everyone, Just got to the stage of fitting pistons into the bores of my 400/4. Been rebuilding it for a few years so thought I ought to get a move on ! New rings fitted so a bit worried about possibility of breaking them. Any tips on fitting, should I use clamps that fit round piston and compress rings or just try and use hands to compress them? Advice much appreciated.
4
« on: May 20, 2018, 10:46:58 AM »
Thanks Mike I can see what you mean, thanks for the tip.
5
« on: May 18, 2018, 08:31:41 AM »
Thanks Fogdevil for the advice.
6
« on: May 17, 2018, 08:40:39 PM »
Thanks Julie that's good news! That's how I had it the first time I assembled it, but after checking the exploded diagram I changed it because it looks like it's on the other side. That put the alignment out. All looks good now. Onwards and upwards ! Thanks again for taking the time out to help. By the way name is Dek ( Derek) the Andeks is combination of Ann ( my wife) and me Dek. Just thought I'd say.
7
« on: May 17, 2018, 07:39:58 PM »
Thanks for the photos Julie. On the nearside top photo is there a removable spacer on the inside of the fixed spacer ?
8
« on: May 17, 2018, 06:15:56 PM »
Thanks Julie for the quick reply. I have checked the exploded view and have put the top, rear spacer where it shows, but bottom, rear doesn't line up. Photo would be greatly appreciated.
9
« on: May 17, 2018, 05:47:03 PM »
Hi All, Trying to refit 400/4 engine in frame and struggling to remember where engine bolt spacers go, I know I should have noted before stripdown but its been a while now. put the top rear bolt and spacer on in the order what I thought but bottom rear doesn't line up with the gap. Can't find a decent picture of the engine in frame. Any help much appreciated.
10
« on: November 01, 2017, 07:15:49 PM »
Thanks John All sorted.
11
« on: November 01, 2017, 01:09:52 PM »
Hi All,
Could anyone please point me in the direction of a set of oil pump 'o' rings please. I have bought a new set of seals but doesn't include new seals for fitting the pump.
thanks Dek
12
« on: June 12, 2017, 09:17:10 AM »
On further inspection I've noticed there is no pivot insert in the horseshoe so maybe it's been done to take up the slack with the blade just dropping in the empty cavity to save a strip down !
13
« on: June 11, 2017, 05:01:10 PM »
This is it !! [ Guests cannot view attachments ]
14
« on: June 11, 2017, 04:31:08 PM »
Sorry having trouble uploading !!
15
« on: June 11, 2017, 04:24:04 PM »
Hi all,
I am rebuilding my 400/4 engine after complete strip down, engine case clean up. didn't notice on strip down but looking at cylinder head cam chain pivot I have discovered the housing has a nut welded between it and the bracket as attached photo. Anyone any idea why, and if its ok to fit as is.
|