Show Posts

1

Project Board / Re: Doms CB550F1 project

« on: April 25, 2024, 11:42:25 PM »

Quote from: DomP on April 25, 2024, 11:31:05 PM

Oh, I misunderstood the speedo cable thing Roo, I assumed it plugged into the end of the standard cable which concerned me as it'll be hugely long by then. Which cable was this and was it from Digital speedos?

The tacho is from digital speedo’s and I think the cable connector is from Louis Moto, I got it from there as DS’s didn’t have one in stock. If I get chance tmrw I’ll dig the paperwork and get the deets for you

Yeah, the cable turns the original rotational, speedo drive into a pulse that the tacho can read. It has to be set up like everything which I haven’t got round to yet but the reviews are really good and it was perfect for what I was doing.

Sent from my iPhone using Tapatalk

2

Project Board / Re: Doms CB550F1 project

« on: April 25, 2024, 11:19:54 PM »

Betterer look

Sent from my iPhone using Tapatalk

3

Project Board / Re: Doms CB550F1 project

« on: April 25, 2024, 11:18:45 PM »

Crap photo but during jogging mudguards. That’s the electric pick up on the drive there. It had a fettle after this for better clearance but works a treat and keeps a look………kinda

Sent from my iPhone using Tapatalk

4

Project Board / Re: Doms CB550F1 project

« on: April 25, 2024, 11:13:27 PM »

That’s crap maye, hope she’s see’s some improvement soon mate.

The job list is endless and there’s always something else to sort! I’ve some spare black coated brake lines lurking in the draw. They’re the ones from the solid section off the calliper to the splitter, not sure of the configuration you’re using but I bought them after getting sums wrong and ended up being a bit short. I had some remade so these are surplus.

I went for the single tachometer, digital speedo combo from Daytona. Looks pretty classic, small and has all you need on yer know…….possibility for you?
I run a digital connector from the OE speedo drive the same route as the cable would go up to the clocks. Fairly inconspicuous……

Sent from my iPhone using Tapatalk

5

Project Board / Re: Doms CB550F1 project

« on: April 25, 2024, 10:16:53 PM »

Loving that Dom, really getting there now mate, top progress

Sent from my iPhone using Tapatalk

6

New Member Introductions / Re: Hi Newby

« on: April 25, 2024, 07:45:07 PM »

Ehyup Kev, enjoy

Sent from my iPhone using Tapatalk

7

Humour / Bless ‘em,……….snigger!

« on: April 25, 2024, 01:19:37 PM »

Sent from my iPhone using Tapatalk

8

CB500/550 / Re: 550f master cylinder

« on: April 24, 2024, 04:05:10 PM »

No worries mate

Sent from my iPhone using Tapatalk

9

CB500/550 / Re: 550f master cylinder

« on: April 24, 2024, 01:00:45 PM »

Boxed up and ready to go, I’ll get it posted today or tomorrow Dom if that’s cool beans with you?

Sent from my iPhone using Tapatalk

10

CB350/400 / Re: Fully restored CB400/4 on eBay

« on: April 23, 2024, 04:03:19 PM »

Deffo left

Sent from my iPhone using Tapatalk

11

CB500/550 / Re: 550f master cylinder

« on: April 22, 2024, 09:56:33 PM »

Quote from: DomP on April 22, 2024, 09:48:38 PM

Quote from: Laverdaroo on April 20, 2024, 07:41:51 PM
If you need one, I’ve got one in a re-built state with new piston and some paint if you need one mate

Sent from my iPhone using Tapatalk

I'm wondering if there might just be enough clearance as the reservoir tapers off doesn't it? Are they 1/2" Roo

Do you want me to bob them over to you Dom, then you can shuffle them about to see? Don’t mind mate. CBR’s have clip ons and they fit a treat so I think it’ll fit ok but I don’t mind sending some over to you mate………

Sent from my iPhone using Tapatalk

12