This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - taysidedragon
Pages: 1 ... 83 84 [85] 86 87
1261
« on: December 24, 2015, 05:54:23 PM »
Looking great. Good work. 
1262
« on: November 18, 2015, 05:59:32 PM »
Great result Roy. I bet that was a relief. Lots of time saved there. 
1263
« on: November 12, 2015, 03:40:55 PM »
Go boil your horn! Unbelievable, a great tip. 
1264
« on: October 25, 2015, 05:46:48 PM »
The original type 400/4 kickstart lever. I'm using one from a different model, cb250 I think.
1265
« on: October 19, 2015, 05:10:13 PM »
You could use a strong alloy like Duralumin if you can find some. The plates will have to be thicker than the original steel ones to get the same strength.
1266
« on: September 09, 2015, 12:18:06 PM »
Happy retirement Ian. My dad's now been retired for longer than he worked. I've never seen him smile at something so much! Have a long and happy retirement.
1267
« on: April 06, 2015, 09:46:27 PM »
Cafe Racer Kits do a comstar to spoke wheel conversion kit. Bit pricey, but probably the easiest way to do it.
1268
« on: April 05, 2015, 06:44:02 PM »
There's a torque figure in the manual, can't remember what it is but it's a low figure - 4 or5 lb ft I think.
1269
« on: March 08, 2015, 10:14:26 PM »
Use paraffin (safer than petrol) with a firm brush and, as said, lots of hard work.
1270
« on: January 20, 2015, 04:57:26 PM »
I dealt with Dennis at noxandrattles who supplies Stainless Parts for 400/4 He told me he had stripped lots of 400/4 engines and never came across a washer on the camshaft, Today he contacted meto let me know he was doing the Topend of a 400/4 and lo and behold there was a a washer on the camshaft.
Could it be a spacer shim, so only there if needed?
1271
« on: January 16, 2015, 03:48:01 PM »
I made a cheap, easy bearing retainer removal tool out of a piece of steel flat bar and 2 short 4mm bolts.
Just drill 2 holes in the bar the same distance apart as the holes in the retainer, tap the holes 4mm and screw in the 2 bolts. If you don't have any taps you could drill clearance holes for the bolts and use a nut to hold them in position, just use slightly longer bolts.
They should locate in a pair of holes in the retainer and unscrew it nicely. Mine came out no problem, no damage and I'll keep the tool handy for future use.
If you've got a really stubborn one(oo-err!) and worried about damaging the retainer it would be quite easy to make a wider one and fit 4 bolts to fit all 4 holes on the retainer.
If that doesn't work then by the time you get the retainer out it will be scrap. New ones are available and quite cheap.
1272
« on: January 16, 2015, 03:14:02 PM »
Both my bikes have survived the winter ravages so far. They're both safely tucked up in the garage which is part of the house. If the garage loses it's roof the whole house has gone! Some Dundee drivers can't understand the need to slow down at all on snow or ice and have been throwing themselves off the road at regular intervals. http://www.thecourier.co.uk/news/local/dundee/car-crashes-into-dundee-flat-as-snow-brings-chaos-to-dundee-s-roads-1.784823The bikes will be out on the rare occassions the roads are dryish and not covered in salt and slime. Roll on springtime!
1273
« on: January 02, 2015, 01:49:02 PM »
When I cleaned up the exhaust ports on my 400's head I prised out the old gaskets only to find a second set of gaskets underneath! The exhaust gaskets are crushable to form a seal, so you should use new ones each time. Sump washers in alloy or copper are just plain washers so can be annealed to soften them for re-use. Don't heat them to red hot though, they're not mild steel. Just heat them up and quench in cold water. Dry off and ready to go.
1274
« on: November 26, 2014, 10:00:35 PM »
On all my sohc hondas the braided lines completely replace the whole brake line, caliper to master, some still use the junction on the yokes, others move the front brake switch to a banjo in placevof the pressure switch on the yoke. My bikes are cb550 and 500 so may be a bit different.
Great. That helps a lot. Cheers.
1275
« on: November 26, 2014, 09:29:34 PM »
I bought a set of braided hoses for the front brake but the bottom hose is much longer than the standard one.
It's long enough to go all the way to the caliper without using the metal brake line. Is that ok as long as it's secured away from the wheel?
If it is, I've got a brand new repro metal brake line going spare!
Pages: 1 ... 83 84 [85] 86 87
|
Show Posts