76
CB350/400 / Re: rear sprocket
« on: July 28, 2019, 11:20:41 AM »
Picking my words carefully My rear wheel spindle measures from under the head a tad over 10.1/2 inches Approx Just under 27cm
Try our new info resource - "Aladdin's Cave" (Main menu)
Just added a separate link to Ash's Dropbox thread (shortcut)
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to. 76
CB350/400 / Re: rear sprocket« on: July 28, 2019, 11:20:41 AM »
Picking my words carefully My rear wheel spindle measures from under the head a tad over 10.1/2 inches Approx Just under 27cm
77
CB350/400 / Re: rear sprocket« on: July 28, 2019, 10:39:51 AM »
Just had a look at DSS and they list two types The type i have (chrome end for tommy bar ) is for the F & F1 The long bolt type Julie has is the correct type / style for the F2 Although the parts manual lists this as fitting F & F2 So i guess they are interchangeable as the bearings are the same for both Ross
78
CB350/400 / Re: rear sprocket« on: July 27, 2019, 10:02:19 PM »
AS you say if it does the job I will fit it as i see fit, then fit exhaust, If it needs turning round no probs
79
CB350/400 / Re: rear sprocket« on: July 27, 2019, 09:24:23 PM »
Who's right and Who's wrong That is the question??? lol TrickyMicky has an early 400 with footrests on the arm and his spindle is the same as mine His arm are closed ends Mine are open end So maybe i have the early style spindle with later style arm !!!!! Parts catalogue shows both type arms but only one type spindle?Don't know why ??
80
CB350/400 / Re: rear sprocket« on: July 27, 2019, 07:48:32 PM »
So you can still insert a tommy bar without fouling the exhaust?? Or was the wheel fitted then the exhaust
81
CB350/400 / Re: rear sprocket« on: July 27, 2019, 07:11:26 PM »
Just found in Haynes manual page 97 section 7-1 It states Pull out the spindle with the drive side adjuster and spacer As Trickymicky states would make it difficult fitting a tommy bar to assist removal
82
CB350/400 / Re: rear sprocket« on: July 27, 2019, 03:38:53 PM »
So to conclude It won't matter which way the spindle fits if you have open-ended swing arm But if closed end Nut on brake side so spindle drawn out nearside. Think i will fit nut to brake side although i have open-ended arm
83
CB350/400 / rear sprocket« on: July 27, 2019, 12:57:01 PM »
Just fitting a new rear sprocket and it seems a lot of play Not much rotational just a little bit of movement within the bolt holes of the sprocket The bushings seem ok But lateral play there is at least 1/8" old money Is this the norm Also the rear spindle The PO has put it with the nut on the sprocket side Looking in the parts catalogue thats right Yet in the service manual shows nut on brake side which i believe to be correct Your thoughts appreciated Cheers Ross
84
CB350/400 / Re: oil seals« on: July 11, 2019, 03:57:46 PM »
It was really quick. Luckly all still fresh in my mind around a couple hours give or take Hardest part was lifting the engine and turning it over and round A bit of a lump ?? Ross
86
CB350/400 / Re: oil seals« on: July 11, 2019, 03:44:53 PM »
Engine split, Seal fitted, and all back together. Thanks for your advice Julie and Roy It had to be done properly. Didn't dare risk it, then have to pull the motor out thanks again Ross
87
CB350/400 / Re: oil seals« on: July 10, 2019, 08:08:49 PM »
Luckily I've got time on my side and not in a rush Just that the manuals are very vague and not fully informative Not like the forum Your right Julie do it once and do it right Better to find mistakes at this stage Least i can leave the Barrels and Head on Ross
88
CB350/400 / Re: oil seals« on: July 10, 2019, 07:03:33 PM »
Bummer!! Thanks guys Back to schooooool !!!!!!!!! As I'm waiting for some parts from D S America to arrive Think its safer to split cases and do the job properly Ross
89
Engine rebuild coming on fine, after Head rebuild and rebore by Trigger. Just one problem I didn't fit the right hand crank seal before bolting the cases back together. I now not sure which way it fits. Logic says looking at it , the metal side out. Is this correct ?
Thanks Ross 90
Tricks & Tips / Re: HONDA CB VOLTAGE REGULATOR TEST ETC« on: July 09, 2019, 02:06:11 PM »
T ;Dold you the trouble was under the left hand cover??? All that time at night school not wasted then
|