This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Skunky
16
« on: October 06, 2018, 05:05:44 PM »
Been watching a few bikes on Ebay over the past few months.
Can't understand why people are having bidding wars when there are days and days to go before the auction ends.
All it does is push the price up, great for the seller but not the bidders.
One I was watching recently, 6 days to go, 2 people out bidding each other, whats the point?
Am I missing something?
No you're not. Stops you getting in with that last 10 second bid. I think what can happen is someone bids big early and then people start fishing to see how high they went. Obviously not poker players. Keep the cards close to the chest and Slam them down. I bid 10 seconds to early on my CB400 exhausts and it cost me £60 extra.
17
« on: October 06, 2018, 01:47:43 PM »
Cant be K0 and you have got a lot of work to be able to register that------wheres the front brake?
Brakes would only spoil the Bobber look
18
« on: October 06, 2018, 01:39:55 PM »
Still, The carburettor rebuild is nearly complete. All the carbs have been scrapped scrubbed and cleaned in an ultrasonic cleaner, tops and bowls polished, new jets needles and seals fitted and reassembled. Then Disassembled as the light dawned on the missing spring. A manual set up bench set up to get it as close as possible to factory and then should be able to get a start. One tip I could pass on. I managed to rescue the floats but the pins were of course ruined. I bought a 2mm model makers brass rod from fleabay for £2.99 for 200mm and cut my own pins rather than pay £2.50 each for them. Still got enough for another rebuild . Got my eyes open for a set of Vacuum gauges but in no hurry.
19
« on: October 06, 2018, 12:50:48 PM »
👍. Are you on your hands and knees looking for it somewhere on the floor?
No Found the ball bearing on the workbench. Never found the spring. Managed to re-purpose one from some bmw bits I had left over.
20
« on: October 06, 2018, 11:59:31 AM »
Hands up if you have been caught out by the spring and ball bearing on carburettor 4 choke lever assembly [ Guests cannot view attachments ]
21
« on: October 06, 2018, 08:06:58 AM »
[ Guests cannot view attachments ] Parcel arrived replacement tank, speedo and switchgear thanks to Vortex
22
« on: October 06, 2018, 06:57:00 AM »
23
« on: October 06, 2018, 06:35:37 AM »
German Cross rear light Really?
24
« on: October 03, 2018, 09:35:59 AM »
What Julie said.
Another drawback with pod filters is having to protect them from water ingress when you wash the bike.
Or if its raining hard
25
« on: October 02, 2018, 10:55:17 PM »
Thanks Julie, I will add a lid to my shopping list
26
« on: September 30, 2018, 07:27:47 PM »
Hi people, I was wondering whether there is any advantage to using Pods rather than the OEM air filter. They look quite cool but I'm not sure either way. by the way should the OEM air filter housing have a lid. I don't have one on mine.
27
« on: September 28, 2018, 11:01:48 PM »
Really depends on what you want Ricardo. If you are going for a restoration and you want chrome wheels the're not that expensive to buy. Probably better to buy old ones from ebay rather than trying to strip the others back.
28
« on: September 28, 2018, 10:57:43 PM »
Hi guys,
nowadays due to health, terrible roads here, traffic from hell and having the attention span of a goldfish any bikes are just an ornament that I pass the time of day buggering about with. It's in the blood.
Welcome Steve, If you need someone to take the 500 for a run........ Seriously you will find it easier to handle that the Harley plow puller. Remember your retired and take it out when its quiet. Plenty of lovely b roads in your region.
29
« on: September 25, 2018, 01:30:58 AM »
Hi Jorge, I have a super sport too. If yours has stood as long as mine had you might find the carbs are seized if the fuel wasn't removed first. Also most of the rubber will be perished. Its not a cheap project, but it really depends on how it was left and why it was left. The way it was stored has a great bearing on the amount of work required. Put up some pictures and maybe start a thread on the project board.
Welcome to the nuthouse
Skunk
30
« on: September 25, 2018, 12:53:50 AM »
The postman came today. Don’t you love it when he brings something shiny. If I outbid you for this beauty then I don’t apologise at all 😂😂 [ Guests cannot view attachments ] [ Guests cannot view attachments ] [ Guests cannot view attachments ]
|