Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Woodside

Pages: 1 2 3 [4] 5 6 ... 57
46
New Member Introductions / Re: Oldboy
« on: November 21, 2019, 10:15:13 AM »
That looks pretty smart...and clean
Smaller k0 fork ear reflectors by the look of it ...


47
CB350/400 / Re: Powder Coating Devon / Cornwal
« on: November 19, 2019, 08:46:08 PM »
I have a mate who has olive and black passivate..
I all I need to do is get my platers to zinc my parts and not put any clear on then get them over to my pals asap and dip them...
Shouldn't be to bad as he is only about 15mins from the platers......or just paint it.?

48
CB350/400 / Re: Powder Coating Devon / Cornwal
« on: November 19, 2019, 07:05:04 PM »
Black passivate makes sense.
You can just about make out a colour under the crud

49
CB350/400 / Re: Powder Coating Devon / Cornwal
« on: November 19, 2019, 06:22:22 PM »
Is the plate for the electrics black or zinc?

50
CB500/550 / Re: A Dutch ad for a change CB500K2-ED
« on: November 07, 2019, 10:09:40 PM »
Oops...even says Dutch up top.

51
CB500/550 / Re: A Dutch ad for a change CB500K2-ED
« on: November 07, 2019, 09:30:06 PM »
Looks interesting that site if only I could read german...I'm sure I could translate it on the phone somehow...
Just goes to show not everything on websites is correct ..
Shouldn't the k0 fuse panel have round pin plugs?

52
CB500/550 / Re: Original finish on K0 carb clips
« on: November 06, 2019, 03:12:42 PM »
These are nos...unsure of model but definitely look drab
Shame they have not been stored to well but should clean up

53
CB350/400 / Re: REPLICA EXHAUST FOR 400/4
« on: October 29, 2019, 06:40:02 PM »
, I could do with just the bottom section of this switch so I don't have to butcher a good one, maybe even one where the lug has snapped or the cable adjuster has stripped out. If I can't find one I'll butcher the one I've just bought, which would be a shame really.

I think I may have some here that were stripped or bust so I'm sure I can help

54
CB750 / Re: CB750 K1 Tool Kit?
« on: October 29, 2019, 04:51:42 PM »
I wasnt looking for these but I had just read this thread and these jumped out at me ...2 types

https://www.ebay.co.uk/itm/Honda-NOS-CB500-CB750-Spark-Plug-Wrench-Replated-89216-323-000-H23/392415772160

https://www.ebay.co.uk/itm/Honda-NOS-CB500-CB750-Spark-Plug-Wrench-Replated-89216-323-000-H23/392415741245



55
Humour / Edward munch
« on: October 28, 2019, 07:50:39 AM »
I have just had  this pointed out to me..

Was edward munch just trying to paint a spaniel but was just abit shit.?....so he just went along with it.

56
CB500/550 / Re: Price extremes!!!!!
« on: October 18, 2019, 04:29:24 PM »
Is this the same green bike going for auction...
Still hopefull with that reserve..

https://www.carandclassic.co.uk/car/C1167253

57
CB500/550 / Re: colour of yokes and headlight shell
« on: October 15, 2019, 07:56:02 PM »
The parts are identical except for the pinch bolt holes...

So with a 8mm bolt D washers are required.
7mm no D washer needed ....???

58
CB500/550 / Re: colour of yokes and headlight shell
« on: October 14, 2019, 07:54:57 PM »
It came from the same place as this one...
Notice it also has the bolts fitted to it..
Turns out there were a few there

And no I didn't pay that price for it

https://www.ebay.co.uk/itm/Honda-CB500-CB550-NOS-Steering-Top-Yoke-Arch-53230-323-305/332907452367

I'm pretty certain this was in the bag with the loose part number still in it as you would expect

59
CB500/550 / Re: colour of yokes and headlight shell
« on: October 14, 2019, 07:52:00 PM »
I will have to measure tomorrow as the one I'm using is now newly painted .
But I did hold the nos one up to it..
The fork diameter looks identical.
And the distance between fork also.

The only noticable difference I can tell at the moment is the larger holes on the k0 one for the pinch bolts .

When the piants cured abit I will check it out properly

60
CB500/550 / Re: colour of yokes and headlight shell
« on: October 14, 2019, 07:34:57 AM »
Nope. bag wasn't sealed and part number was taped to it..
And bolts were already fitted.


Pages: 1 2 3 [4] 5 6 ... 57
SimplePortal 2.3.5 © 2008-2012, SimplePortal