This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Woodside
Pages: 1 ... 50 51 [52] 53 54 ... 57
766
« on: October 15, 2014, 10:43:23 PM »
Trigg not worried at all. I'm just curious as to how much has survived...as I'm cleaning all the grime and filth from it it really intrigues me? That rubber cap looked like a lump of grease and crap built up...
767
« on: October 15, 2014, 10:34:04 PM »
Pics here
768
« on: October 15, 2014, 10:26:11 PM »
Tonight I thought I better make a bit of headway on the 400....progress was halted abit by the ramp being needed by the 450....
I have took the gopping top box of and removed the fairing a while ago....i have since picked up some original bars....the ace bars are growing on me so I will leave them for now.
Whilst all the front brake is of I thought I would remove the wheel and give it a clean and pop a new tyre on at the same time...the disc nuts still have what I belive is the factory yellow paint on the end
Is this correct
I also just started to give it a bit of a clean and came across this little split end tube thing
I think it is part number 17358-374-000. Tube assembly drain? (jesus I'm turning into a 400 nerd)
Now these must get slung probably not replaced especially with the split end cap on it.....
So apart from the ace bars I don't reckon this has been apart ( let's not get into the clutch guide thing)
What do you guys think. And what else should I look for as to back this up
769
« on: October 02, 2014, 06:37:21 PM »
Bottom stripe 2.5 mm
Top stripe 4.00mm
3.5mm in between
If I get what you mean?
770
« on: September 27, 2014, 10:40:16 AM »
Tell me if I'm wrong but it does just look like a standard frame that's been coated ....
And I looked at the sellers history. It looks like he knows his bikes...
771
« on: September 27, 2014, 10:22:02 AM »
Before I post it is it just the one you need
772
« on: September 26, 2014, 07:52:11 PM »
I've not forgotten
Just sent a pm I think...
Ill get on it first thing
773
« on: September 25, 2014, 09:40:02 PM »
Pm replied...I'll dig them out tomorrow.
774
« on: September 25, 2014, 09:15:05 PM »
I have an old set of 627's from a 500
Someone will need to tell us if the parts are the same . I haven't a clue....if they are ill pop one out for you
776
« on: September 25, 2014, 07:10:13 PM »
As much as I hate to think any of our hondas were slung together on a budget...
Is it possible the engineers and accountants had a meeting that went...
Acc..."We need to save money on the cam journals"
Mech..."but if we do that they will need to change the oil every 3000 miles?"
Acc..."ok sounds good..stick it in the manual"
777
« on: September 22, 2014, 08:27:45 PM »
What was that company that used to metal spray surfaces like that, and then machine them down?
Joy Engineering? Think they went bust. Must be someone else....
Phill joy engineering Still about and race tuning Hondas ....
778
« on: September 19, 2014, 09:42:06 PM »
Clean it ....stick a lamp holder in the top and sell it as a desk lamp......probably get 500 quid in London for it...
779
« on: September 19, 2014, 09:38:10 PM »
Gonna buy a exhaust and a clutch cable guide this evening and store for 40 years
Money in the bank me thinks?
780
« on: September 19, 2014, 09:36:15 PM »
I like that
Probably get one when they start to go rusty ?
Pages: 1 ... 50 51 [52] 53 54 ... 57
|
Show Posts