This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - shifter
1
« on: April 21, 2024, 09:24:21 AM »
Have anyone willing to sell me a working starter motor for a 1976 cb 200. .?..another option what other model uses the same starter ,
2
« on: April 28, 2022, 11:39:03 AM »
I have been trying to purchase with no avail a gearbox shaft ( sprocket end) "oil seal" , NGK AE1061F.. I'm wondering if some one can help me where to purchase for a CB200 .. I didn't want to remove the one that's in the bike incase non availability...
3
« on: May 24, 2021, 08:24:16 AM »
I have acquired a cb200 ,compression was not good having stripped down both top rings are broken I am going to fit New rings no bore wear really , am a bit confused to ring gap as the manual spec states end ring gap 6thou, but many people say times x the bore (55.51) x 4 = 9 thou . Can someone advise me what gap I should go for .
4
« on: November 24, 2020, 07:23:39 PM »
Is there any member can tell me how many Links in the cam chain on a CB200T , Thankyou for your infill
5
« on: November 09, 2020, 02:20:46 PM »
Having acquired a couple of cb 200’s to restore im wondering if someone can give me some insight as the easiest way to remove engine from frame ie can it done without removing starter motor etc or any other tips ,as when I come to refit into a newly powder coated frame I try and avoid scratching frame ,
6
« on: September 15, 2020, 08:40:09 PM »
Can someone tell me the colour code ( Lime Green ) also ( Red ) for a 74 cb200 , DuPont or other. Appreciated if so ..
7
« on: September 06, 2020, 08:53:13 PM »
can someone clarify if supposely to have small O rings attached to the air screw on the 069a carb ,in front or behind the small spring, or not have any at all .
8
« on: August 30, 2020, 09:49:17 AM »
I am thinking of buying a CB72/77, can anyone point me in the right direction as what to look for , regarding engine longevity etc,40k ,and rebuilds, many thanks .
9
« on: April 04, 2020, 04:59:26 AM »
Can someone advise me on best spark plug to use on a 550 f1 ,standard air box , 069a carbs . Many Thanks.
10
« on: January 18, 2020, 06:06:29 PM »
Have anyone a picture of the best route to fit a fuel filter on a 550 f ,from the tank as it’s a little cramped.
11
« on: April 25, 2019, 11:47:31 AM »
Been ask a thousand times I expect, am planning to replace the camchain tensioner on my 550, is it easy or possible to do this in situ in frame by removing cam cover and head etc .. would appreciate some tips etc if possible. Cheers ..
12
« on: February 22, 2019, 05:14:05 PM »
Anyone attending Bristol Classic Bike Show @ the Bath & West Showground nr Shepton Mallet tomorrow..
13
« on: September 24, 2018, 05:51:08 PM »
Can anyone advise me where the neutral gear switch is located as having no life in the warning light in the speedo as i would like this to illuminate ,if there is no easy fix will have to wait engine out in winter months ,just wondered if any S90 owner have had this problem,
14
« on: May 09, 2016, 08:42:27 AM »
Can someone advise me on which model no iridium plugs to put in a 76, 550 f1, ?
15
« on: January 16, 2016, 06:46:34 PM »
Bristol classic bike show (Carole Nash ) Feb 6th/7th nr Shepton Mallet .
Any members exhibiting their shiny restored prize examples at this show that's held 6/7th Feb ,,
|
Show Posts