Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - shifter

Pages: 1 2 [3] 4 5 ... 8
31
Project Board / 550 f1
« on: January 18, 2020, 06:06:29 PM »
Have anyone a picture of the best route to fit a fuel filter  on a 550 f ,from the tank as it’s a little cramped.

32
Other Bikes / Re: Re-polishing fairing screens
« on: June 07, 2019, 09:17:25 AM »
Hi , I’ve gone through the process with wet/dry grades then Sprayed  with clear coat 2pack as we have done with faded plastic car headlights with great results. .... hope this is some help ....

33
I think your best bet is bite the bullet and spray again ,save time etc as you wouldn’t be happy with it as every time you passed the bike you will look at it first ,no touch up etc etc ,with cover  better than full blast over ,££££.  “ s...e happens “.....

34
CB500/550 / Re: Camchain tensioner fitment 550
« on: April 26, 2019, 06:55:05 AM »
Many Thanks Guys for the  advice ... much appreciated .....

35
CB500/550 / Re: Camchain tensioner fitment 550
« on: April 25, 2019, 03:35:56 PM »
Thankyou Bryan, one of the previous owners have knackered the slot on the adjuster which I recut with the dremmel also the thread is non serviceable , so I was looking for some tips I have previously taken the cam cover off etc (holding rockers up with elastic bands when refitting) it’s just about taken the head off in the frame also the removal of the tensioner, armed with (6 sided sockets etc ) Clymer/Haynes , As you say will replace seals while I’m there ,  so new guide and blade do you think .( my bride (70) says I have no patience ONLY  when messing with engines , must have been an Hgv syndrome 😜, thanks again ...

36
CB500/550 / Camchain tensioner fitment 550
« on: April 25, 2019, 11:47:31 AM »
Been ask a thousand times I expect, am planning to replace the camchain tensioner on my 550, is it easy or possible to do this in situ in frame by removing cam cover and head etc .. would appreciate some tips etc if possible. Cheers ..

37
Out & About / Bristol Classic Bike Show
« on: February 22, 2019, 05:14:05 PM »
Anyone attending Bristol Classic Bike Show @ the Bath & West Showground nr Shepton Mallet tomorrow..

38
Announcements / Re: New Knee
« on: November 29, 2018, 10:17:51 AM »
Keep on top of painkillers (take before pain kicks in 3.1/2 hrs ) it will be fine, make sure you do your excersizes ,don’t give up on them and you’ll be running around like a goungun.  All the best and you’ll be right for  swinging your leg over for 2019..

39
Announcements / Re: New Knee
« on: November 29, 2018, 02:39:29 AM »
Keep doing the exercises, (you will get there ) I was riding a sh300 within 3weeks but that was naughty also don’t judge yourself with others that have same operation , everyone is different but ( you will get there ) , I’ve had two total knee & a hip replaced  I’m back like a 20yr old loving my 750 vfr / 550 /s90 , I also no chick just reaching 75yrs .. oh when your back fit double up on your knee sliders 😀...best of luck , you will get there ......

40
CB350/400 / Re: Bike Security
« on: October 11, 2018, 02:44:40 AM »
I leave the bride sat on the bike when out and about , workshop has air horns on each door  , and a certain weapon aiming from the bedroom window , BEWARE not shy .....

41
CB350/400 / Re: Painting underside of mudguards
« on: September 26, 2018, 07:02:40 AM »
When I restored my TR4  I painted the underside  with a rust preventive  primer  then a rubberised under seal flattened then a polyethylene topcoat ,.. as the harder the paint ie two pack paint will chip. With poly paint being more flexible the stone wii bounce off without chipping..

42
Other Bikes / Re: Anyone with SOHC S90
« on: September 25, 2018, 07:30:23 PM »
Yes Ash, it had three previous owners all in an around York its where i acquired it in 2013 , it had been semi restored in the 90s and then stored in a shed, i rebuilt the wheels new DID rims ss/s spokes, recovered the outer cover on seat,   foam was in really good nick , checked out the motor (someone had thrown a fair bit of wedge at it), carb /tank was in a bit of a state (tank) a week full of coca cola with hand full of chippings, flushed out after week , refilled with  vinegar for another week .. result brilliant., it had previously been sprayed in celli, so i had the tank done in 2pack in case of petrol spillage , really good match (fiat 152).. fitted a new old stock speedo £££ (not Chinese).. And now the neutral ind light works, happy bunny, thanks for the info Hairy..

43
Other Bikes / Re: Anyone with SOHC S90
« on: September 25, 2018, 05:05:25 PM »
many thanks Hairy,that explains it clearly,

44
Other Bikes / Re: Anyone with SOHC S90
« on: September 25, 2018, 12:50:27 PM »
No luck in finding switch, [ Guests cannot view attachments ]

45
Other Bikes / Re: Anyone with SOHC S90
« on: September 25, 2018, 12:45:03 PM »
Hi hairy , trying to post S90 pic .. [ Guests cannot view attachments ]

Pages: 1 2 [3] 4 5 ... 8
SimplePortal 2.3.5 © 2008-2012, SimplePortal