This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - waffey
Pages: 1 2 [3] 4 5 ... 13
31
« on: March 22, 2021, 09:20:03 AM »
OddJob,
I dont have any tension on the spring, thats my issue i believe. I get the tension when the pedal is pressed but when it returns the pedal is floppy as with the spring. Just thinking.........Do i need the footrest installed for it all to work properly, ie the peday return is stopped by the foot rest......i think this could be a Doh moment?
32
« on: March 21, 2021, 09:03:09 PM »
Hi, still struggling with this damn spring. Any pictures of where ther inside spring locates pleaseeeeeeeeeeeeeeee...
33
« on: March 15, 2021, 05:37:39 PM »
O'm thinking the green spring piece highlighted should go where the red line is?
34
« on: March 15, 2021, 04:03:18 PM »
Nurse Julie,
can you get a picture where the small end of the spring sits on the inside of the frame? Thats the bit that is confusing me.
thanks for the other picture, i saw that in another thread
ta
35
« on: March 15, 2021, 01:54:18 PM »
36
« on: March 15, 2021, 01:50:26 PM »
phew, just as well they are ok to use as I ordered one last month in preparation for the build
37
« on: March 15, 2021, 01:48:57 PM »
Hi,
i did look at some of the older post reference the rear brake return spring.
I'm sure mine is wrong as the spring does not have any tension. Please take a look at the pictures and tell me where i have gone wrong!
Thanks
38
« on: March 10, 2021, 01:26:32 PM »
OK, thank you. I'll have another look and swap the the hose around.
39
« on: March 10, 2021, 09:26:14 AM »
Help again!
There seems to be a lot of 'extra' brake hose (see pictures) how does this route at the top? Also, assume the unions with teh bend attaches to the the brake 'thingy' with the brake switch?
40
« on: February 17, 2021, 06:22:50 PM »
had to cut my 1977 stand off.
I then tried to get the tube out by sawing through it, gave that up as I didn't have the patients for it. sourced a second-hand stand that was all freed upped, bought the new solid pin and installed that. jobs a goodin......less time sawing and swearing, more time drinking"!!!!!!!!!!!!!!!!!
to be fare I always way up time taken versus buying something after time is money.
enjoy the sawing!
41
« on: February 17, 2021, 06:15:10 PM »
thanks very much for the photos and advice, its good to do a sanity check.
42
« on: February 16, 2021, 05:55:03 PM »
Hi,
having a bit of drama with bits n bobs on the Honda. So I've stopped working in the headlight and electrics as my little brain is confused.
I thought I would add the front brake hose assembly etc. Can someone take a picture of it attached to the forks (brake block that holds the switch) and just for comfort, around the caliper itself/
thanks in advance
43
« on: February 12, 2021, 12:34:39 PM »
i used my bench grinder using some abrasive disc's then a polishing mop with auto sol. They come up ok, I didn't plan to get all the large dents out.
44
« on: January 29, 2021, 04:38:25 PM »
I just emailed Marcel (CB750Faces.com) to see how much a set of CB500K2 faces will be now landed in the UK inc import duty etc.
order some faces, two chrome rings and trip boot <£80 delivered tracked postage
45
« on: January 29, 2021, 04:30:11 PM »
Thank you
Pages: 1 2 [3] 4 5 ... 13
|
Show Posts