This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - DomP
1
« on: Today at 03:37:38 PM »
What actual model is it and where is the ignition switch now?
Hi Bryan, it's my cb550f1 with the hugely long centrally mounted ignition barrel which I'd like to move somewhere more discrete
2
« on: Today at 11:16:07 AM »
Yeah Motogadget was just a step toofar financially for me, I keep thinking 'cheap build remember, cheap build' 🤣
I'm sure an electrical genius will answer my query
3
« on: Today at 08:16:26 AM »
Looking at the wiring diagrams I seems the 4 wire switch has two browns linked into one, I wonder if its as simple as doing that?
4
« on: May 13, 2024, 05:34:04 PM »
Chatting with Roo earlier when he suggested I used the old K style frame mounted ignition, I could make up a bracket if I can't find an original but there is a wiring difference - 5 wires on my F as opposed to 4 on a K switch. Is there a wiring solution?
5
« on: May 12, 2024, 09:50:35 PM »
Pm sent Julie
6
« on: May 12, 2024, 03:58:35 PM »
That sounds the answer Julie, do you have any idea how he did it?
7
« on: May 12, 2024, 03:27:15 PM »
Do any of you electrical guys know a good solution for my cafe racer build? I'm looking to either relocate the ignition or change it to keyless to make room for my centrally mounted gauge, any thoughts appreciated!
8
« on: May 06, 2024, 08:05:44 AM »
I can only think that it's tying up on the bearing Ted, maybe you need to drift it in ever so slightly more?
9
« on: May 05, 2024, 05:37:56 PM »
I have a local source for most O rings
A company called Hayley Group
On a local industrial estate, the Hereford branch are really helpful,
Imperial, metric,fuel resistant etc,
And the bonus, normally a fraction of the cost of NOS,
Take a sample, and the item, like tappet cap ,they will find the size needed
Sent from my SM-A546E using Tapatalk
Now you tell me John!😄
10
« on: May 05, 2024, 08:27:35 AM »
I'll fill it up with stuff in no time I'm sure, I'd have lived to have gone bigger but I'm doing it within permitted development rules (I think) and getting this far has cost a small fortune
11
« on: May 05, 2024, 08:18:22 AM »
Maybe get the block skimmed which will make the oring recess slightly shallower, that's what I did following Brian's advice after he rebored my block. I used Vesrah gaskets from DS
12
« on: May 04, 2024, 01:39:27 PM »
It's 7200 x 4800, yeah I do feel a bit knackered today but I did have 2.5 helpers. Making a concrete chute through the hedge out of corrugated tin was the best idea I had, it made it so much easier, oh and hiring a speed float and easy screed followed by 3 pints while it began curing😀
13
« on: May 04, 2024, 12:42:29 PM »
14
« on: May 04, 2024, 09:41:31 AM »
Pics
15
« on: May 04, 2024, 09:37:28 AM »
There's not really a right place for this but yesterday was concrete pour day for my workshop (day job) to make space in my current place for my bikes. 5m³ of concrete is quite a lot to move and level, I'm aching a bit today!
|
Show Posts