Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Nurse Julie

Pages: 1 ... 340 341 [342] 343 344 ... 523
5116
Out & About / Re: OUT AND ABOUT 2018
« on: August 09, 2018, 08:28:27 PM »
Smashing looking bike Dennis and a lovely backdrop in the pics.

5117
Project Board / Re: CB750K4 New project
« on: August 09, 2018, 05:30:35 PM »
Great news, these things are easy when you send off everything they need to do the job !!!

5118
CB350/400 / Re: Tank postage
« on: August 09, 2018, 05:26:48 PM »
Yea, not getting worried yet!!!!
You should be able to track it throughout the whole journey Dave, you could also email Menno to see if its arrived. I have had tanks get there in 3 days before now but 5-7 is more the norm.

5119
CB350/400 / Re: Tank postage
« on: August 09, 2018, 05:13:58 PM »
Website don't wanna give me one  :'(
Have you clicked on International?

5120
CB350/400 / Re: Tank postage
« on: August 09, 2018, 04:53:25 PM »
Hi Julie do you know how long they usually take to get there ,the courier picked mine up last Friday afternoon ,
5-7 days usually. Have you looked at the tracking info?

5121
CB750 / Re: Getting cb750k on centre stand
« on: August 09, 2018, 02:19:47 PM »
If it makes you feel better Simon I have never, ever been able to get a CB750 on the center stand, I struggle with a CB 500/4 and CB550/4 but I can do the CB400/4 on a good day but it has to be a very good day !!!

5122
CB500/550 / Re: Tapered head bearings question
« on: August 08, 2018, 09:31:17 PM »
All Balls but make sure the seal is included.

All balls part number....596955#WZJLPK, comes with both seals and all the washers etc.

5123
Project Board / Re: CB750 Barn find project - First Timer
« on: August 08, 2018, 07:09:00 PM »
Agree with Rob, the more protection you give the frame, the better. But, too much protection, you wont have room left to lift it out. Still very difficult to do even with 2 people, if you twist or tilt the engine in the frame even by a few mm, it will get wedged and then it is a nightmare. It is a pain but in the long run, stripping the bike down and lifting frame off is easier in the long run.

5124
Project Board / Re: A RUF 750
« on: August 08, 2018, 06:14:02 PM »
Agree 100% with Hairy and £2500 isn't enough of a fine. There is absolutely no excuse to be holding and using a phone in this day and age. Personally, I think looking at sat navs whilst driving is as bad if not worse.

5125
Where's My Old Bike? / Re: Looking for my old CB750
« on: August 08, 2018, 04:49:11 PM »
It's been off the road for a very long time. [ Guests cannot view attachments ]

5126
Pop rivett it on but put a couple of foam pads behind it to stop it rattling.

5127
Project Board / Re: NEW PROJECT CB750 K1
« on: August 07, 2018, 10:04:56 AM »
Making great progress Paul, on the road by the weekend ?😆😆😆

I wish ;) How long does Meno take for the painting just wondering when to get them sent off too him.
ASAP if I were you Paul. Depending on the work you need done on the tank it could take quite a few months.

5128
Project Board / Re: NEW PROJECT CB750 K1
« on: August 07, 2018, 09:08:35 AM »
Making great progress Paul, on the road by the weekend ?😆😆😆

5129
CB750 / Re: 750K2 getting ready for registration
« on: August 06, 2018, 10:08:06 PM »
😀😀😀😀😀😀 I have  a picture in my mind of Mick sitting on the loo, wearing a dress, painting his toe nails and then going out mixing wall paper paste in to his engine oil......

5130
CB500/550 / Re: Dating help and insurance woes
« on: August 06, 2018, 10:04:45 PM »
Well done you......and Ken, the right result.

Pages: 1 ... 340 341 [342] 343 344 ... 523
SimplePortal 2.3.5 © 2008-2012, SimplePortal