This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Bryanj
1
« on: April 15, 2024, 07:26:24 PM »
Thats a good price, i have a freing in nashville and a medium box is $30
2
« on: April 15, 2024, 03:47:26 PM »
Dont forget usps only do air mail and as soon as you say "fuel" its a special item, even if new and never had any in it
3
« on: April 15, 2024, 03:42:21 PM »
Looking at that i suspect the caliper is as bad so i would use a greas gun to pump the caliper piston out then thouroughly clean, reseal and new stainless piston.
Grease gun method
Standard grease gun remove the fitting that clips on the grease nipple.
Leave bleed nipple in
Remove the steel brake pipe from caliper and caliper brom bike
GENTLY screw the caliper pipe thread onto the grease gun N.B. it will only go on a few threads as they are different BO NOT FORCE IT.
Pump away and watch the piston for movement.
This has never failed me but does leave the piston full of grease to clean out!
4
« on: April 15, 2024, 08:26:12 AM »
It depends on exactly which bike it is please specify as there are two different ways it works and youcan dodamage if you do it wrong
5
« on: April 13, 2024, 08:39:07 PM »
Nobody sells seperate pipes anymore only sets, cheapest was posted on here a while ago but for you cms in netherlands might be a better bet
6
« on: April 13, 2024, 08:36:08 PM »
Also points surfaces corrode when not used and pivots sieze up
7
« on: April 13, 2024, 07:07:56 PM »
I dont believe Honda would design it so you had tofit to lower case and get opperating mech out of way to mate cases but i suppose anything is possible, none of the other hondas i have worked on 50cc tp 1500cc have done that
8
« on: April 13, 2024, 04:39:37 PM »
I have been in garage repairing door today and found a complete unit that came from usa, piston is out and needs replacing, you can have it for what it cost me plus post
9
« on: April 13, 2024, 04:34:34 PM »
Sorry to read that Ted, life can be a real swine at times but together we survive, i have started loosing siblings and that brings a new focus
10
« on: April 13, 2024, 04:28:35 PM »
Cant watch videos so here is my 2 penorth
Points gap at 14 thou and timing spot on the F, it takes a lot of time, patience and practice to get BOTH spot on.
Sounds like the carbs need syncing, there is arie up of mine on here somewhere
Possibly tight, or loose tappet clearance.
You say you have cleaned the carbs, have you split them and had them ultrasonicaly cleaned?
11
« on: April 12, 2024, 06:25:56 PM »
On the pipe union or bleeder, i have repair kits for the bleeder
12
« on: April 12, 2024, 06:25:02 PM »
Points gap and timing first
13
« on: April 12, 2024, 06:24:12 PM »
Eggcup full of parafin wouldve sortrd that! But seriously well done, we just need to hear the running
14
« on: April 12, 2024, 03:34:10 PM »
Dont know why you took it apart, would have run as it was!
15
« on: April 12, 2024, 03:32:03 PM »
400,500,550 all the same mate, whats wrong with yours
|
Show Posts