16
CB500/550 / Re: De horned
« on: March 16, 2024, 01:56:21 PM »
I ordered a set of 3 magnetic trays from Toolstation a couple of years ago. I don’t think they realised they were magnetic and I got 6.
Try our new info resource - "Aladdin's Cave" (Main menu)
Just added a separate link to Ash's Dropbox thread (shortcut)
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to. 16
CB500/550 / Re: De horned« on: March 16, 2024, 01:56:21 PM »
I ordered a set of 3 magnetic trays from Toolstation a couple of years ago. I don’t think they realised they were magnetic and I got 6.
17
CB500/550 / Re: First start after rebuild« on: March 08, 2024, 09:53:27 PM »
When I did my 650 top end, with the rocker cover off and the plugs out I spun it over gently on a battery drill.
18
Member 4 Sales / Re: Job lot 500/4 mainly« on: March 08, 2024, 09:19:49 PM »
I might be going tomorrow, if so I’ll pop over and say hello.
19
CB500/550 / Re: Will it fix?« on: March 07, 2024, 07:07:56 PM »
What about the low temp aluminium brazing rods on eBay?
I’ve used them before and they are pretty good. 20
CB500/550 / Re: Will it fix?« on: March 07, 2024, 10:43:34 AM »
I think Nurse Julie had a couple of these for sale recently.
21
CB500/550 / Re: Delkevic Exhausts.« on: March 06, 2024, 01:12:28 PM »
That’s good to know, I’m not ready to fit mine yet.
Mines currently still boxed on the kitchen floor, missus is not happy. But then she rarely is 22
Misc / Open / Re: Casting rubber parts« on: February 29, 2024, 10:11:29 PM »
I need to refine mine a bit, the polyurethane I used is way too hard.
23
Misc / Open / Casting rubber parts« on: February 29, 2024, 02:14:07 PM »
3 of the rubbers holding my battery box on my 550 are shot.
They are not available so I thought I’d make some. Made a 2 part mould in the lathe and got some polyurethane liquid rubber stuff. For a first attempt it came out a treat and there was no shrinkage. The new one is a slightly different shape because it was done on the lathe. May get a new mould 3D printed so it will be the correct shape. Top pic is the old one. 24
CB500/550 / Re: CWC spokes« on: February 29, 2024, 01:29:38 PM »
My mate has just placed an order from these guys, I’ll let you know what they’re like when they arrive.
He’s ordered stainless for his RD250 https://e-spokes.eu/ 25
Desperately Seeking!! / Re: Im assuming at some point ill need to balance my Carbs - can anyone reccomend...« on: February 29, 2024, 12:58:02 PM »
I’ve got these, very good
Www.carbtune.com 26
CB500/550 / Re: Delkevic Exhausts.« on: February 24, 2024, 11:09:18 AM »
Just checked all 4 pipes, no markings of any kind.
FYI, kit comes with everything you need. Brackets, bolts, copper sealing rings, clamps and collars. Even the rubber bump stops for the stands. It’s a lot of money but a hell of a lot cheaper than the other source of these. 27
CB500/550 / Re: Delkevic Exhausts.« on: February 24, 2024, 09:15:08 AM »
I’ll check them later on and let you know.
28
CB500/550 / Re: Delkevic Exhausts.« on: February 23, 2024, 06:56:48 PM »Yep, might hang it on the wall insteadWell, it’s arrived and is absolutely gorgeous.So you're pleased with it then Steve 😁😁😁 29
CB500/550 / Re: Delkevic Exhausts.« on: February 23, 2024, 06:56:13 PM »Steve - no Spooning please - it might invalidate the warranty. 30
CB500/550 / Re: Delkevic Exhausts.« on: February 23, 2024, 05:04:54 PM »
Well, it’s arrived and is absolutely gorgeous.
|