Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Nurse Julie

Pages: 1 ... 342 343 [344] 345 346 ... 526
5146
CB750 / Re: CB750 F1 Shocking news. (photos)
« on: August 10, 2018, 10:02:36 AM »
We use TEC shocks on all our old Hondas. Excellent quality and VFM.

5147
CB350/400 / Re: 400/4 struggles to pick up when warm
« on: August 10, 2018, 09:40:55 AM »
D7EA 

5148
CB350/400 / Re: 400/4 struggles to pick up when warm
« on: August 10, 2018, 08:42:37 AM »
+1 with Mr Hairy and Paul. Check plug type and sounds like its running lean to me.

5149
Lots of places on Ebay sell them. You can 'officially' have a black and white if you wish being a pre 77 registered bike.

5150
Out & About / Re: OUT AND ABOUT 2018
« on: August 09, 2018, 08:28:27 PM »
Smashing looking bike Dennis and a lovely backdrop in the pics.

5151
Project Board / Re: CB750K4 New project
« on: August 09, 2018, 05:30:35 PM »
Great news, these things are easy when you send off everything they need to do the job !!!

5152
CB350/400 / Re: Tank postage
« on: August 09, 2018, 05:26:48 PM »
Yea, not getting worried yet!!!!
You should be able to track it throughout the whole journey Dave, you could also email Menno to see if its arrived. I have had tanks get there in 3 days before now but 5-7 is more the norm.

5153
CB350/400 / Re: Tank postage
« on: August 09, 2018, 05:13:58 PM »
Website don't wanna give me one  :'(
Have you clicked on International?

5154
CB350/400 / Re: Tank postage
« on: August 09, 2018, 04:53:25 PM »
Hi Julie do you know how long they usually take to get there ,the courier picked mine up last Friday afternoon ,
5-7 days usually. Have you looked at the tracking info?

5155
CB750 / Re: Getting cb750k on centre stand
« on: August 09, 2018, 02:19:47 PM »
If it makes you feel better Simon I have never, ever been able to get a CB750 on the center stand, I struggle with a CB 500/4 and CB550/4 but I can do the CB400/4 on a good day but it has to be a very good day !!!

5156
CB500/550 / Re: Tapered head bearings question
« on: August 08, 2018, 09:31:17 PM »
All Balls but make sure the seal is included.

All balls part number....596955#WZJLPK, comes with both seals and all the washers etc.

5157
Project Board / Re: CB750 Barn find project - First Timer
« on: August 08, 2018, 07:09:00 PM »
Agree with Rob, the more protection you give the frame, the better. But, too much protection, you wont have room left to lift it out. Still very difficult to do even with 2 people, if you twist or tilt the engine in the frame even by a few mm, it will get wedged and then it is a nightmare. It is a pain but in the long run, stripping the bike down and lifting frame off is easier in the long run.

5158
Project Board / Re: A RUF 750
« on: August 08, 2018, 06:14:02 PM »
Agree 100% with Hairy and £2500 isn't enough of a fine. There is absolutely no excuse to be holding and using a phone in this day and age. Personally, I think looking at sat navs whilst driving is as bad if not worse.

5159
Where's My Old Bike? / Re: Looking for my old CB750
« on: August 08, 2018, 04:49:11 PM »
It's been off the road for a very long time. [ Guests cannot view attachments ]

5160
Pop rivett it on but put a couple of foam pads behind it to stop it rattling.

Pages: 1 ... 342 343 [344] 345 346 ... 526
SimplePortal 2.3.5 © 2008-2012, SimplePortal