This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - paulbaker1954
Pages: 1 ... 5 6 [7] 8 9 ... 12
91
« on: December 06, 2017, 08:44:12 AM »
Worth picking up a copy if you see one. Not a bad article, features DS and sohc.net but NO MENTION of sohc.co.uk!!!! I feel a letter coming on  Also features a £7995 550 for sale at Fowlers Bristol (nice but overpriced IMO)
92
« on: November 24, 2017, 12:15:16 AM »
Here it is all in place
I used 2 pieces of Al bar bolted to the original coil brackets and fitted the coils to these
The electronic box then fits snugly on top as shown
93
« on: November 16, 2017, 08:14:45 AM »
Just an FYI Eurocarparts have a good offer on with 33% off and free delivery
I just bagged 5l of TripleX 10-40 for £17 all in — - USE CODE SAVE33 at checkout.
Worth stocking up at that price
(Yes I know they always have offer on !!! But not always with free delivery as well)
95
« on: November 12, 2017, 08:40:50 AM »
Could use some advice!!
Rev counter climbs lovely to 5k then sticks there and then jumps to 8k or thereabouts.
I have new cable, squirted some WD up the hole etc and still no better.
I am kind of coming to the conclusion that the P.O. rode around a lot just under or around 5k and it’s developed a “sticky point”
I have 3 alternatives
1) Send it for repair ( but that does look very expensive from the research I have done.
2) Source a fleabay replacement (not much around) and may be just as bad.
4) Have a bash at stripping it myself and seeing what I can do.
So now to my question, has anyone got any experience of repairing these units. I think they use a magnetic rotor system so are pretty simple so hoping a good strip and clean will sort it
96
« on: November 10, 2017, 02:06:15 AM »
I just finished fitting the Boyer system to my 4 but learned a hard lesson on the way that I thought I’d share.
The Boyer instructions say to remove the bob weighs and springs but do not make it clear you also have to remove the advance/ retard cam off the advance/ retard unit shaft as well.
I missed this and was confused as to why the stator plate did not fit properly and why the mag rotor fouled the chrome cover.
In my confusion I filed off the lugs on the end of the advance unit to get it to fit (unsuccessfully) without fouling the cover (thanks to Ash for replacement advance/ retard unit)
The answer was simple as always in hindsight, in that if you don’t take off the cam bush the stator plate won’t fit over the end of the advance unit properly and the mag rotor won’t fit over the end of the advance unit shaft.
It all comes down to a missing comma!!
Instruction 16 in the Boyer instructions says
“Remove the cam bobweights and springs from the advance retard unit”
It should say
“Remove the cam, bobweights and springs from the advance retard unit”
Amazing what confusion a missing , can lead to!!
As the saying goes
“Eats shoots and leaves” or alternatively “Eats, shoots and leaves”
I have notified Boyer by the way !!!
97
« on: November 04, 2017, 11:48:58 PM »
Does anyone happen to have a spare one knocking about in a box of bits am desperately seeking one complete with dowel pin also
Fingers crossed😀
98
« on: November 01, 2017, 10:15:46 AM »
Hi Folks
I saw in a post a while ago some images from a member of their BOyer installation using some made up brackets (as opposed to the "tie wrap" approach.
I cant find the post can anyone direct me please
99
« on: October 30, 2017, 01:04:47 PM »
Just taken the plunge and ordered the full kit with Micro coils after months of deliberating !!
I have a question re plug caps mine are NGK purply colour ones (sorry for the crap description)
Are these OK for use with the BOyer system? Is there an easy way to check them?
Cheers all
100
« on: August 25, 2017, 05:03:01 PM »
I keep seeing references to K0 crankcase shapes as being square and got me wondering
My bike was made Oct '71 and both engine and frame numbers start with a 1
but I am not sure what a "square" case looks like
Is mine a K0, here's a pic. By the way never noticed the bent fin before opinions on trying to bend it back or leave it !!!
101
« on: August 20, 2017, 04:50:49 PM »
Anyone recommend a source of decent front fork gaiters
My DS aftermarket ones have both split after 1k miles
Not impressed😂😂
102
« on: July 30, 2017, 03:54:25 PM »
Been, like a few thinking of fitting a Boyer kit when I have some spare pennies.
I have identified kit 00089 for existing coils or kit 00289 that comes with coils.
I have a set of new aftermarket coils, so was thinking of using 00089 but what is the required primary resistance for kit 00089. Is there any advantage from using the Boyer coils in anyone's experience?
Also, can anyone recommend a supplier, as the Boyer site links only to 2 U.K. Distributors but they don't list the Honda kits on their web sites
Sorry if I am asking what has been asked many times before.
103
« on: July 17, 2017, 08:50:12 AM »
Nice sunny day out at this small event, free to go and just rock up when you want.
Here's a pic of my four trying to be a Royal Enfield.
Lover the Landy Defender "Lion" corner and the mini ice cream van (very welcome !!).
Interested in the Honda BOSS NC25 (believe these were a grey import) - sadly didn't track down the owner.
Nice little show and worth turning up next year if your are reasonably local.
104
« on: July 04, 2017, 09:31:22 PM »
Anyone likely to rock up?
I went 2 years ago it's a small event but you can just show up for free stay as long as you want have a brew and a chat
I met someone there 2 years ago with a nice 750 four
Pages: 1 ... 5 6 [7] 8 9 ... 12
|
Show Posts