21
SOHC Singles & Twins / Re: CB360 Wiring question
« Last post by McCabe-Thiele (Ted) on Today at 10:59:00 AM »Brake pressure switch?
Try our new info resource - "Aladdin's Cave" (Main menu)
Just added a separate link to Ash's Dropbox thread (shortcut)
21
SOHC Singles & Twins / Re: CB360 Wiring question« Last post by McCabe-Thiele (Ted) on Today at 10:59:00 AM »Brake pressure switch?
22
Desperately Seeking!! / Re: CB400 Rear Brake Rod 43451-377-000« Last post by Deano400 on Today at 10:58:41 AM »Thanks Dave, will take a look.
23
SOHC Singles & Twins / Re: CB360 Wiring question« Last post by AndyD on Today at 09:44:42 AM »I think that light green / red is used for neutral switch / light on the CJ models so maybe that somehow?
I also seem to remember that there were one or two unused wires somewhere on the CJ loom but can't recall where. Cheers, Andy 24
CB350/400 / Re: Anyone recognise this bit?« Last post by Laverdaroo on Today at 01:10:24 AM »You legend, cheers for that. I actually thought they were fixed in the cap or part of it. Never knew they came out at all. Brill, that’s a great result
Sent from my iPhone using Tapatalk 25
CB500/550 / Re: Rear wheel rotation stiffens up when tightening axle problem.« Last post by McCabe-Thiele (Ted) on Today at 01:00:47 AM »It's probably between my ears rather than reality - when I did my rectification fit of the right bearing instead of using my lump hammer as previously to get it fully home - I used my Orange Plastic shot filled hammer for the final strike - thinking it might stop a rebound.
26
CB350/400 / Re: Anyone recognise this bit?« Last post by McCabe-Thiele (Ted) on Today at 12:33:03 AM »Well spotted Ozzybud I did not realise they come out!
Knowing your luck Roo it will be the last one you check that's missing! 27
Project Board / Re: Teds new project a CB500 K1 mostly version 0.5 circa 1972.« Last post by McCabe-Thiele (Ted) on Today at 12:24:20 AM »Yes they are already painted in gloss Black in safe storage - done by the bloke in Ilkeston who was recommended to me by a sohc member (Seaman Phil?).
No petrol tap or filler cap fitted as yet - I have a tap kit & new filler cap to fit. All the big ticket items purchased just some minor oddments for the final fettle. 28
Project Board / Re: Teds new project a CB500 K1 mostly version 0.5 circa 1972.« Last post by magpie114 on Today at 12:16:15 AM »Looking very good, can’t be too far off. Are the tank and panels finished?
Sent from my iPhone using Tapatalk 29
CB350/400 / Re: Anyone recognise this bit?« Last post by davidcumbria on May 09, 2024, 11:56:42 PM »You can see it 3 min and 13 sec in this video
https://youtu.be/wFaFIsYXiPc?si=R4AT1defc8MSov1N 30
CB350/400 / Re: Anyone recognise this bit?« Last post by ozzybud on May 09, 2024, 11:52:41 PM »i just had my carbs apart to adjust the needle height it is a part of the internal linkage in the diagram under #9. on the left side of the 9 box area it is the third bit down from the top. it slides up into the screw.. without it i would think getting the carbs in sync would be very difficult... I was very amazed how many pieces there were inside the carbs just for the linkage. Honda had some amazing engineering going on but this assembly is complex to say the least.
|