Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Crispy

Pages: [1] 2 3 ... 12
1
Desperately Seeking!! / CB750 K1 Clutch pressure plate
« on: March 20, 2022, 04:00:38 PM »
Anyone got one they are willing to part with?
CB750 K1 clutch pressure plate part no 22350 300 010 / 030

2
Project Board / Re: Honda CB750K5 Restoration by Royhall
« on: February 16, 2022, 03:55:37 PM »
Philpotts did a great job on my fork top nuts, they were really chewed up. I sent them in with the fork top tubes and rear axle.  Great thread, enjoying reading it, good luck.

3
Announcements / Re: Beautiful…
« on: February 15, 2022, 10:04:25 AM »
Lovely looking bike! Having a bike like that in a space like that is something I've always hankered after. Nice one!

4
Also booked in, looking forward to a nice 🌞 sunny day and some good company! 👍

5
I'd be up for that as well next year now the bike is finished and registered. 👍

6
Project Board / Re: 750 K1 project
« on: October 16, 2021, 08:54:48 AM »
That really is a thing of beauty.

Cheers

Dennis

Thanks Dennis  :)

7
Project Board / Re: 750 K1 project
« on: October 16, 2021, 08:52:12 AM »
Thanks Andrew, its taken a while for various reasons , but we got there in the end.

8
Project Board / Re: 750 K1 project
« on: October 15, 2021, 06:30:22 PM »


Now go and cut that cable tie holding the clutch cable to the frame tube.

Haha! It's a reusable tie I put on temporarily, I don't want to cut it I'll replace it with an ordinary one. I also need to connect the carb drain tubes up before anyone mentions them!  :)

9
Project Board / Re: 750 K1 project
« on: October 15, 2021, 06:22:59 PM »
Thanks for the comments everyone!  I couldn't have done it without the help of this forum and its members you have been a mine of information, and practical assistance, thanks.

10
Project Board / Re: 750 K1 project
« on: October 15, 2021, 04:54:00 PM »
After a year long wait for a set of HM300 pipes this K1 is now  almost finished, just a few finishing touches needed. Much to my surprise and delight It fired up straight away, and all seems good, it sounds terrific, much throatier than my old K2.  Just need to register it with DVLA now and get it on the road.

11
Misc / Open / Carburettor in action
« on: July 02, 2021, 05:54:03 PM »
Thought this you tube video, (if you haven't  seen it before) was worth  a watch!  Clear bodied carburettor  in action!
https://youtu.be/toVfvRhWbj8
https://youtu.be/toVfvRhWbj8

12
CB750 / Re: 341 replicas
« on: January 07, 2021, 09:26:01 PM »
Nice! I've been saving for a set of the 300 exhausts, now I've got the funds no one has any stock! 🙄😂😂

13
CB750 / Re: HELP ... NOT ENOUGH HOLES IN MY CARB BACK PLATE 😢😢😢
« on: November 20, 2020, 07:04:36 PM »
Couple of photos showing the left hand pipe routed around the back , and a front view of the pipes coming through the back plate.

14
CB750 / Re: HELP ... NOT ENOUGH HOLES IN MY CARB BACK PLATE 😢😢😢
« on: November 20, 2020, 06:55:59 PM »
Perhaps they are routed like the K1?  the second (Left hand side) fuel pipe comes around the back and through the upper second hole on the right hand side?

15
Project Board / Re: 750 K1 project
« on: September 21, 2020, 06:56:34 PM »
Looking good. Love that colour scheme, one of the best. Local painter???
Cheers Tim, it looks great in the flesh, photos seem to change the tone a bit. Dream Machine, Long Eaton painted it. Done a good job .  ;)

Pages: [1] 2 3 ... 12
SimplePortal 2.3.5 © 2008-2012, SimplePortal