This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Seabeowner
Pages: 1 ... 57 58 [59] 60
872
« on: May 27, 2016, 09:43:28 AM »
Makes you wonder, as you can pay £3+ each for these.
I paid £4 for three and thought I was doing ok.
Anyone know a source of the grommets that are on the mudguard stays etc.? At nearly £12 for a mudguard set, there must be another source.
Phil
873
« on: May 25, 2016, 09:49:20 PM »
Thanks Alan, I'll let you know.
Phil
874
« on: May 25, 2016, 09:22:37 AM »
Alan, If you take a pic of the profile (or draw around) with a rule or tape alongside and post it it would be useful. I am going on the material being about 13mm wide and 1mm thick unless you tell me otherwise.
Thanks, Phil
876
« on: May 24, 2016, 06:36:56 PM »
Both of my 500 engines had the rod in two.(not broken) One had been very badly machined with a stub that fitted in a hole in the other part.
The other one had been done well, with a perfect part sphere machined into both parts (the LHS is short, only about 50mm) and a steel ball between the two. It has lasted for a number of years even though it is just in the ali. I check it every year and smear a little moly grease on it.
878
« on: May 23, 2016, 07:12:02 PM »
Hi, Have three 500/550s and none have the air filter retaining spring. Need advice to make, as not great at this.
Channel looks to be about 13mm. What type of steel to use and approx what thickness (gauge). I can use the cmsnl pic for approx shape unless anyone has anymore detail.
Thanks, Phil
879
« on: May 19, 2016, 06:56:18 PM »
I have an F1 and had trouble getting a fork stanchion for this model. Strangely cruzinimage did not list them on ebay.uk and bought 1off from Germany. Only found the cruzinimage ones by searching ebay Australia!
There are listed three different fork tubes for the CB550:
K1, K2: 51410374003
F1: 51410390003
K3, K4: 51410404003
The differences are to do with the oil damping holes and some forks have a rebound spring and some not, but I never did find all the details.
This pic from an ebay listing in the US gave some detail of parts that the F had over the K1.
880
« on: May 19, 2016, 06:12:01 PM »
I have a couple of the oil control valves. Think they came from a cb550, but are the same I think.
PM me if interested.
881
« on: May 10, 2016, 06:34:46 PM »
And DSS have eased their price up £30+VAT and only 10off left.
882
« on: May 04, 2016, 12:31:53 PM »
Ok I think I know your problem.
I have an unrestored US K3 import sitting in my garage. The cables are routed to the LHS of the tank. The bars are 75cm tip to tip and about 11cm rise. Also restoring an F1. Just measuring the opening cable, the K3 cable is about 6cm longer.
Opening cable measuring the outer: Not including the 90 deg bend the K3 is 92cm to the end of the threaded section at the carbs. My F1 cable is 86cm.
Phil
883
« on: April 14, 2016, 06:35:22 PM »
Just cleaning up this bolt on my F1. It is a fine thread as standard M12 x 1.25.
884
« on: April 12, 2016, 07:14:31 PM »
Old subject. But just getting my 500K1 ready for its first MOT in 10 years. I have the clunky forks when putting the bike on the c/s. I had one of these back in 1974 and I don't ever remember the clunk. But I had just come from 3 years of Triumphs so maybe anything was an improvement.
Is it the damper rod clunking against its endstop when extended and has anyone had an issue at MOT? Testers don't like clunks, but as already said on the c/s is not real world.
thanks
885
« on: March 07, 2016, 12:01:03 AM »
Advice please.
Engine all stripped down. Should I always replace the 34mm plug on the end of the gear mainshaft? Part no 91207-374-000. Any ideas why it is special order from DS? And what is the difference between the CB550 and the CB400 plug (91207-333-000)..they appear to be the same dimensions.
I also need the crankshaft seals and CMSNL do a set with all seals including the plug which seems cheap at 19 euros +VAT. If anyone has this set, are the crankshaft seals correct with the location flange at one end as the pics are rubbish?
Thanks folks. Phil
Pages: 1 ... 57 58 [59] 60
|
Show Posts