Recent Posts

Pages: [1] 2 3 ... 10
1
Misc / Open / Re: What happens if an exhaust mounting stud snaps off?
« Last post by Bryanj on Today at 08:12:09 PM »
On an old bike it was always stated at estimate time that any extra work due to broken/siezed bolts was at the expense of the owner
2
Project Board / Re: Mike's CB550 Project
« Last post by Bryanj on Today at 08:06:28 PM »
You wana smell the stuff that comes out of a Leyland lock up flywheel on a coach, its burn the ovies if you splash it
3
CB500/550 / Re: NGK plugs for 500
« Last post by Bryanj on Today at 08:04:53 PM »
I have always used NGK resistive caps and non resitor plugs simply cos thats what the rep said, never asked why as he was very knowledgeable
4
Project Board / Re: Project CB350F
« Last post by magpie114 on Today at 08:03:00 PM »
Finally got the correct rear sprocket, tried all the usual places but I had overlooked Honda Classics. Looking for a stainless f/brake caliper piston and a couple of other items I typed CB350f in the site search bar and there amongst the parts was the sprocket. Ordered online Tuesday evening, delivered Thursday morning and the pegs fit correctly.

[ Guests cannot view attachments ]

I’ve been checking the placement of the various washers on the brake stay arm. The rubber washer had previously been fitted (apparently incorrectly) on the outside of the stay instead of next to the brake plate. Confusingly the owners manual shows it on the outside.

Also I initially thought the parts diagram of the stay at the swing arm was wrong - shouldered bolt, torque arm, 10mm spring washer, 8mm plain washer then nut. However I suppose this allows some movement of the arm whilst retaining some tension.
5
CB350/400 / Re: Engine assembly questions/tips
« Last post by Nurse Julie on Today at 07:59:03 PM »
Graphogen on all new surfaces that are going to touch each other, a drop of oil on everything else, except underneath the shells, you fit these dry.
6
SOHC Singles & Twins / Re: CB360 Wiring question
« Last post by Bryanj on Today at 07:58:49 PM »
You are welcome, having done a few imports it gets easier!
7
CB350/400 / Engine assembly questions/tips
« Last post by Dolomite_ on Today at 07:49:48 PM »
It's almost time to start putting my engine back together, just waiting for the last bits to be aqua blasted and bolts zinc plated.

Just thought I'd ask the question again, what assembly lubes would people recommend? I've seen quite a few mentioned.

Should I put anything in the cylinders? I've seen people mention a few drops of oil, graphite lube, and nothing.
8
SOHC Singles & Twins / Re: CB360 Wiring question
« Last post by Craizeehair on Today at 06:56:40 PM »
DLR disconnected and all good now. Thanks for the help.
9
CB500/550 / Re: Candy Garnet Brown
« Last post by AshimotoK0 on Today at 06:54:18 PM »

I presume you mean 500mL un-thinned as it normally comes from a apint supplier,(thins 50/50%) ... If so yes plenty enough.

For black panel:-

 https://www.paints4u.com/Customer/ProductDetails/Index/12003

[ Guests cannot view attachments ]

10
CB500/550 / Re: NGK plugs for 500
« Last post by McCabe-Thiele (Ted) on Today at 06:50:04 PM »
My experience on cars before individual coil packs arrived was that many used resistor caps and resistor plugs without problems with one coil on 4 & 6 cylinder engines so it's a new thing for me to consider it.
Pages: [1] 2 3 ... 10
SimplePortal 2.3.5 © 2008-2012, SimplePortal