This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - Arch stanton
1
« on: May 05, 2024, 01:05:09 PM »
Hello. Am I correct in thinking. Replacing the oem spring clip on the top of the kickstart. Is an impossible task?. Or has anyone here any tips or advice they could offer. As I am fresh out of ideas. Tia Sean.
2
« on: March 30, 2024, 03:10:10 PM »
Hello fellow members. I have just been out for a run on my Sloper. First time it's been out in a couple of years. Great little bike. But unfortunately. I have lost a Baffle from the oem exhausts. I don't suppose there are any fellow members, who may have a spare baffle they would be willing to sell. Would there? Yours living in hope. Sean.
3
« on: December 26, 2023, 09:02:45 PM »
Hello. I have a very nice CB175 K6. Built using about 80% nos parts. The wheels are original. I polished the spokes about 10 years ago. But a few are now showing rust. Even though it lives as an ornament in my living room. So I ask. Should I just replace the rusted spokes, have all the spokes re, plated, replace with new zinc spokes or stainless. Thank in advance.
4
« on: July 14, 2023, 07:15:26 PM »
Hello. I have just noticed my front Bridgestone tyre has worn quite badly on the rh side. After only about 2k miles. This cannot be normal, surely. At this rate. I'll be using 2 fronts to 1 rear. Can anyone shed any light on this please. Thanks in advance. Regards. Sean.
5
« on: March 30, 2023, 07:06:53 PM »
Hello. Has anyone else on here received any strange invoices from Marcel? I ask this because. This afternoon I received a email invoice from Marcel, stating my account has been paid. Dated 2018! I would ask him directly. But being a bit of an IT dunce. I am reluctant to do so in case his computer has been hacked. A bit odd that i get a invoice 5 years after the transaction. Sean.
6
« on: January 15, 2023, 08:19:05 PM »
Is there anyone on this forum who has a Cb175k0?
7
« on: July 16, 2022, 03:11:22 PM »
Hello. Is anyone aware of a H4 headlight unit, that will fit in the standard shell of the 175k6? Tia. Sean.
8
« on: November 17, 2021, 12:54:17 PM »
I am currently playing around with a Xl125k2. Which has no engine. But i have a Xl185 engine, which i will try to fit into the 125 frame. But whilst comparing parts. I noticed the throttle slide in the 125 carb. Is much larger than that in the 185 carb. This i found surprising. Can anyone explain. Why the extra 60cc would need a smaller carb slide? Sean.
9
« on: November 03, 2021, 04:52:10 PM »
Hello. Does anyone know a colour match for Cb550f1 orange? Regards. Sean.
10
« on: May 06, 2021, 10:16:29 AM »
Hello. Does anyone here know where the main earth point is supposed to be? I would have assumed it to be near the coil. But there is no sign of the usual green wire with a ring terminal there or anywhere else. Regards. Sean.
11
« on: March 31, 2021, 10:15:59 PM »
Is it me. Or is the headlight switch on the 750 k1. Dangerous? Is there an alternative?
12
« on: February 27, 2021, 08:47:11 PM »
Hello. Can anyone tell me the original finish on the case screws on cb250rsa ? Tia.
13
« on: February 15, 2021, 10:19:16 AM »
Hello. Can the bottom crankcase be removed. Without disturbing the top end of the engine? Tia. Sean
14
« on: January 03, 2021, 06:44:01 PM »
Hello. I wish to know. How many Xl250 Motorsports, Honda sold in the UK. I know the 125 sold well. But the 250's were very scarce. Can anyone advise where to find this info. Regards Sean.
15
« on: December 04, 2020, 06:40:44 PM »
Who wants one. Before it goes in the bin? When I typed Clymer. Auto spell wrote "Clunker" 🤔
|