This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Seabeowner
Pages: 1 ... 57 58 [59] 60 61
871
« on: June 17, 2016, 05:31:05 PM »
The downpipes on my F are pretty good and I had designs on getting the old silencer repaired or modifying another to suit.
DS ore OOS of the gasket (packing) that goes between the two. It is a simple tube, but does any body know what material it is or I should use.
PN 18391-390-405
Thanks
872
« on: June 16, 2016, 10:49:11 PM »
This ones for Ash I think. Do you have a guide for fitting new HT leads to coils as my leads on the F are hard and cracking? The leads are formed to a tight bend at the exit of the coils and I am afraid to move them here. Joining pieces for HT leads seem pricey.
Plus, has anyone used Z650 coils or similar as they seem to have replaceable leads and will they fit if I make new mounting brackets? I still have points ignition.
Thanks
873
« on: June 12, 2016, 05:14:39 PM »
Mr T, Sent you my no earlier. Did you get it? If you are working days, can come Tuesday eve.
Cheers
874
« on: June 10, 2016, 11:18:33 PM »
Yes Menno that would be me.
MOT next week or so and then I will fit the newly painted tank and panels and also have have new DS pipes to fit and finally post a picture. Nice work, but still sitting carefully wrapped on the spare bedroom!
875
« on: May 30, 2016, 12:34:02 PM »
Mr T. Not a lot of help today, as going away. But am only just down the road in Maidenhead. PM me if you like and we can compare notes etc. Back 9th.
876
« on: May 30, 2016, 12:24:08 PM »
Wow Spitfire at least you are making me feel young. I started on £20 a week and the avatar pic is my CB500 that I paid I think £720 in August 74 from HGB in Harrow.
Phil
877
« on: May 29, 2016, 10:10:55 PM »
I sorted out my old mags a while ago and I also have both of these and was reading through the rebuild this afternoon!
With horror I came to the picture of the clutch on P44 and read the line about the orientation of the top clutch plate. It is also in bold in the shop manual. I've just bolted up my 550F engine. I have no manual for the 550.
But I did have tucked away a clutch assy from a 550K1 and one from for a K3. Both do not seem to have the swept grooves in the top friction plate. Presume that the idea was dropped as a waste of money and 550s all have straight cut grooves.
Phil
879
« on: May 27, 2016, 09:43:28 AM »
Makes you wonder, as you can pay £3+ each for these.
I paid £4 for three and thought I was doing ok.
Anyone know a source of the grommets that are on the mudguard stays etc.? At nearly £12 for a mudguard set, there must be another source.
Phil
880
« on: May 25, 2016, 09:49:20 PM »
Thanks Alan, I'll let you know.
Phil
881
« on: May 25, 2016, 09:22:37 AM »
Alan, If you take a pic of the profile (or draw around) with a rule or tape alongside and post it it would be useful. I am going on the material being about 13mm wide and 1mm thick unless you tell me otherwise.
Thanks, Phil
883
« on: May 24, 2016, 06:36:56 PM »
Both of my 500 engines had the rod in two.(not broken) One had been very badly machined with a stub that fitted in a hole in the other part.
The other one had been done well, with a perfect part sphere machined into both parts (the LHS is short, only about 50mm) and a steel ball between the two. It has lasted for a number of years even though it is just in the ali. I check it every year and smear a little moly grease on it.
885
« on: May 23, 2016, 07:12:02 PM »
Hi, Have three 500/550s and none have the air filter retaining spring. Need advice to make, as not great at this.
Channel looks to be about 13mm. What type of steel to use and approx what thickness (gauge). I can use the cmsnl pic for approx shape unless anyone has anymore detail.
Thanks, Phil
Pages: 1 ... 57 58 [59] 60 61
|
Show Posts