6166
CB500/550 / Re: Cylinder Head stud torque settings
« on: August 15, 2017, 07:16:25 AM »
There only is a dutch arm of CMS!!
Try our new info resource - "Aladdin's Cave" (Main menu)
Just added a separate link to Ash's Dropbox thread (shortcut)
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to. 6166
CB500/550 / Re: Cylinder Head stud torque settings« on: August 15, 2017, 07:16:25 AM »
There only is a dutch arm of CMS!!
6167
Anorak's Corner / Re: Glaring errors in Honda literature« on: August 09, 2017, 03:07:31 PM »
500 four parts book has 4 gear selectors--2 of one part number
6168
Out & About / Re: Out and about 2017 -- forward planning« on: August 09, 2017, 07:44:07 AM »
Whereabouts in Gloucester did you get that mate, might have to visit it
6169
CB500/550 / Re: 550 four k3 alternator rotor coils« on: August 09, 2017, 07:40:28 AM »
nope smaller
6170
CB500/550 / Re: This guy doesn't know what a UK 500K1 should look like« on: August 08, 2017, 03:07:56 AM »
That cap latch is all Honda supply now thanks to the Yanks and safety control, original type catches are only available pattern
6171
CB500/550 / Re: This guy doesn't know what a UK 500K1 should look like« on: August 07, 2017, 06:48:41 AM »
RH switch is US, brake hose not in mudguard clip, rear indicator wiring bodged, different plug caps on two outer cylinders, not woth what hes asking or if it is mine should have been 4 grand not 2
6172
CB500/550 / Re: Frame and Engine numbers« on: August 07, 2017, 06:41:40 AM »
I did say Honda, if Yam numbers don't match its hookey
6173
CB500/550 / Re: US spec handlebars - sorted now, thanks« on: August 06, 2017, 02:34:20 PM »
You are welcome, always new they should be on the correct bike and yours looks good
6174
CB500/550 / Re: Frame and Engine numbers« on: August 06, 2017, 02:32:14 PM »
If i was shown a matching numbers Honda i would doubt its provenance
6175
CB500/550 / Re: Cylinder Head stud torque settings« on: August 06, 2017, 02:30:43 PM »
Dont want to be rude but torque setting is in the manual that you need to do the rebuild correctly
6176
Misc / Open / Re: The 2040 ban on petrol vehicles« on: August 05, 2017, 08:08:31 PM »
Did you know that ALL motorcycles registered since 1st January this year had to be Euro 4 which means fuel injection and ABS, my local MOT man has seen his trade drop by over 50% as there are no cheap 125 Euro 4's which means no gear sales, no servicing and no upgrades
6177
Other Bikes / Re: Strange wiring issue.« on: August 05, 2017, 12:41:38 PM »
Some leds are wired to not be polarity conscious (marker lights on HGV trailers) other are like 501 replacements for wing repeaters as I found out on my pickup
6178
CB500/550 / Re: 550 four k3 alternator rotor coils« on: August 05, 2017, 12:38:39 PM »
Its a varnish type insulation so has to be at damn near melting point to burn off and these motors do get hot
6179
Misc / Open / Re: The 2040 ban on petrol vehicles« on: August 05, 2017, 12:35:52 PM »
As I read it it is TOTALY petrol or DIESEL cars so Hybrids are the norm from then
6180
CB500/550 / Re: 550 four k3 alternator rotor coils« on: August 04, 2017, 10:12:13 PM »
Yes possibly, on that meter the picture shows it set on volts, if the knob is rotated anti clockwise the next section is Ohms the first setting is the highest setting (Mohms) and with the probes together a reading of zero is expected whilst apart there should be no reading showing (infinite) the yellow to steel core should be infinite, if you get any reading turn the knob anti clockwise until you get an exact number and report the number and scale
|