Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Bryanj

Pages: 1 2 [3] 4 5 ... 664
31
Misc / Open / Re: cost of speedo calibration.
« on: March 15, 2024, 08:32:05 PM »
If the front wheels are the same diameter the drive box will be the same, is this Suzuki GT or Kawasaki GT

32
CB350/400 / Re: Parakeet Yellow Paint Code
« on: March 15, 2024, 04:43:47 PM »
Honda did not use "standard" codes so there isnt one, all you can do is colour match

33
Project Board / Re: The rebirth of Lazarus
« on: March 15, 2024, 07:45:39 AM »
Could be porous weld, same sump 500/550 all way through so should be spares about, i may even have one but cant get into my garage till i fix the door, do have a 550 bottom end in the car i will see if it has a sump.on it for you tonight

34
Other Bikes / Re: My Goldwing
« on: March 15, 2024, 07:43:14 AM »
Honda never put a time ,or mileage, on the belts but i recon 80,000 or 8 years is a good idea, at least its not the dumb Ford idea of a "wet" belt inside the engine!
Only thing i ever had to change unusual was the coupling shaft to pinion on a very early wing that did not have a grease nipple

35
Misc / Open / Re: cost of speedo calibration.
« on: March 15, 2024, 07:35:05 AM »
Dont know of any one doing this, are you sure its the correct speedo for the bike and what bike is it?

36
Other Bikes / Re: My Goldwing
« on: March 14, 2024, 01:17:24 PM »
Nice, have you changed the belts yet? Somewhere i have the numbers for Gates ones

37
Project Board / Re: The rebirth of Lazarus
« on: March 14, 2024, 09:24:01 AM »
Possible bad drain plug threead, bad washer(alloy) of cracked sump pan, you need to clean off totally and find where exactly comming from im afraid

38
Coppaslip on threads is fine, fluid on seal and piston sides

39
Project Board / Re: The rebirth of Lazarus
« on: March 13, 2024, 07:21:35 PM »
Check gearchange shaft seal

40
What is it? / Re: Anyone Recognize These Wheels?
« on: March 13, 2024, 10:11:22 AM »
True, but they never mentioned how many times they stopped to pick up detached parts

41
CB500/550 / Re: Delkevic Exhausts.
« on: March 13, 2024, 10:09:48 AM »
Yup, that way you can make sure the little balance pipe fits.
Be prepared to "modify" slightly the bends on the aftermarket brackets to get everything correct

42
CB500/550 / Re: Delkevic Exhausts.
« on: March 12, 2024, 05:58:18 PM »
Assemble everything loosley then work front to back tightening evenly

43
Other Bikes / Re: CL350 carbs
« on: March 12, 2024, 04:20:47 PM »
Unless its been buggered about with all the brass bits should be fine with a clean

44
Misc / Open / Re: Fixing fins
« on: March 11, 2024, 05:07:19 PM »
What bike is it? I have 500 and 550 blocks about at various sizes

45
CB500/550 / Re: 1978 CB550 four
« on: March 11, 2024, 03:04:05 PM »
Its really just a pain in the arse job no matter how you do it but holding the quadrant open can make gatting the lower one on

Pages: 1 2 [3] 4 5 ... 664
SimplePortal 2.3.5 © 2008-2012, SimplePortal