This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - RGP750
Pages: 1 ... 3 4 [5] 6 7 ... 64
61
« on: June 06, 2020, 06:47:20 PM »
you could have said that when you sent the screws   How quick can you get them to me then?
62
« on: June 06, 2020, 06:28:30 PM »
Up date
Did the reseating excersise and just the odd drip every 5 mins
from 2 and 3 but every now and then no 2 drops about a thimble full and then stops. Weird!!
Blasted round float bowl 'o' rings get 5mm longer when they get petrol on them had to hang them in the sun for an hour to shrink back .
4 of the bowl screws also needed tapping out to 5mm, thought I might get away with it yesterday but after a nights sleep thought I need to do it properly .
Plan to have another go at 2 and 3 again tomorrow so hopefully nearly there.
63
« on: June 05, 2020, 08:44:52 PM »
Thanks guys
Thats tomorrows next stinky job then .
I'll report tomorrow night ,fingers crossed
Cheers
64
« on: June 05, 2020, 07:46:32 PM »
Hope to have it on the Road next week Steve,
There was only one leaking when I got it from you and I recon that was the one with the split tube .
Hope I can sort it with one help on here.
65
« on: June 05, 2020, 07:31:44 PM »
Hi strangers not been here for a while .
Almost have the gold 500 back on the road (yours Steve)
carbs totally stripped and ultrasonically cleaned put back together with new float jets and housings. and seals
floats set at 22mm bench tested for leaks and two ctr overflowing . Tried just tapping float bowls ,still leaking .
Took bowels off and result one of the overflow tubes is leaking . all floats are free.
Change for another float bowl
now they are all overflowing Grrrrrr! any thoughts please
66
« on: April 20, 2020, 07:14:56 PM »
I make the plastic parts. you can have some just message me .
I will have to find the stock I made
67
« on: October 14, 2019, 10:19:42 AM »
Wow Ash that was scarey ,almost couldn't watch .
Wonder why they fitted a adv / ret lever to the left hand bars??
68
« on: September 21, 2019, 10:15:07 AM »
Don't worry John mine has just done the same, only been on 2 years . Grrrr!!!!
69
« on: September 18, 2019, 08:45:50 AM »
Silver gaffa with SOHC on it is then. 
70
« on: September 17, 2019, 08:58:01 AM »
Took the K0 for a 140 mile run on Sunday, VMCC charity run, great weather and a couple of other early 70's hondas cb250 and cb360 [ Guests cannot view attachments ]
71
« on: September 17, 2019, 08:54:36 AM »
I'll be there, be good to meet some names on here .. Just need a way to identify, 
72
« on: August 23, 2019, 10:19:04 AM »
Depends what she looks like Brian ,(if i could still see )
73
« on: August 23, 2019, 10:14:46 AM »
Bang on k2-k6 w125. that is at Goodwood and one of the repros.
Our customer just used to bring great chunks of it to us and say 'copy that' kept us busy for a couple of years,
the cylinder block was fabricated around cast exhaust/combustion chamber/inlet and cylinder casting.
74
« on: August 23, 2019, 10:04:46 AM »
light weight at 4 pints ,half a pint and i'm anybodies  ;Ds
75
« on: August 23, 2019, 09:01:06 AM »
Hoping to go this year
Friday Street farm shop and Cafe ,not cheap but good .IP171JX.
Pages: 1 ... 3 4 [5] 6 7 ... 64
|
Show Posts